Chery A15. Manual — part 194
Chery A15 Maintenance Manual
Chapter Four Rear Door
I. Disassembling and Assembling Rear Door
1. Before disassembling the rear door, remove
the decorative board first so that remove the elec-
trical connecting wires may be removed.
2. Loosen the fixing nuts of the bolt for holding the
lining with vehicle body.
3. Remove the electrical connections and the fixing
bolts between the door and the hinge on the front
pole. Another operator disassembles the door.
Place the front door on a flat surface and apply a
protection layer between the door and the contacting
area on the surface.
Assembling procedures for the rear doors are the opposite of the above and bear in
mind that tightening torque for the fixing bolts on the door is 56N`m.
II. Adjusting Rear Door
In case that longitudinal or transverse adjustment of the rear door is necessary, use
tools for internal hinge to loosen the hinged bolts
on the hinge with specified pressure, in a direction
parallel with the level. Loosening should be performed
in a slow way otherwise material fatigue may occur.
Don’t move the tools longitudinally for damage caused
by this can only be remedied through re-welding the
hinge. In order to avoid cracks on coating of vehicle,
coating wax should be used.
Chery A15 Maintenance Manual
Tighten the bolts after adjustment with a tightening torque of 56N.m.
Note: After closing the door, keep the door sealed with the sealing strips around the
opening of the door. If there aren’t any holes on the sealing strips to allow air in, or
the door can not be closed or opened due to improper pressure when closing it.
Remove any of the following parts with the door guard plate being first removed and
proceed according to the instructions in “Interior Lining and Decoration”.
III. Disassembling and Assembling Waterproof Coating
Before disassembling any parts, first remove the
waterproof coating, the lock handle and the
fixing clamp.
Be sure to apply the waterproof coating in a correct
way during assembling. Keep waterproof coating
adhering to the top, side and bottom. In this way
water can flows out and will be kept from leaking into vehicle or damaging door
board.
IV. Disassembling Internal Door Handle
The internal door handle is fixed on the internal
door board through its own structure and screws.
Remove the screws, hold the internal door handle
and push it forward to disassemble it.
V. Disassembling and Assembling Door Lock
Disassembling the lock assembly
1. The lock is fixed on the door frame with two
fixing screws, as is shown by the arrows in the figure.
Chery A15 Maintenance Manual
2. Disassemble the lock device by removing the
fixing clamp between control device and the lock
device.
The manual locking device and the connecting lever
on the installing position of the door lock motor are
coupled with the same clamp.
VI. Disassembling External Door Handle
Disassemble the fixing bolt between the handle and
the door frame. Shake the handle forward and
remove it when it reaches a angle of 90
º
.
There shouldn’t be any rust, fouling or wear on the
lock arms and the control device. Check if the
external door handle and the corresponding lock
body is in good condition.
VII. Disassembling Central Door Lock
Loosen the fixing screws between the central door
lock and the door frame. Disengage the stem com-
pletely from the lock clamp. Remove the cables and
the servo motor.
Assembling procedures for the door parts are the
opposite of disassembling procedures.
Chery A15 Maintenance Manual
VIII. Adjusting Striker Plate
In case that the door can’t be normally closed
because of fault adjustment of the striker plate,
readjust position of the strike plate. The adjustment
operation is to loose the striker plate with a 15mm
wrench and move the striker plate according to the
requirements.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст