Chery A15. Manual — part 55
SHIFT ADJUSTMENT
Neutral positioning:
——Disassemble gearshift knob and protective
cover and fix the gearshift knob according to
the positioning requirement, see the chart (the
black one is positioning assist)
——Leave the pipe clamp at its natural position.
——Clamp nut, fasten by 25Nm.
——Try all the shifts, gear shifting should be
smooth and without stop, secure the validity of
the reverse gear lockup.
Fine adjustment:
——After a long time using of the vehicle, there will
be wear and tear between gearshift mechanism
parts which makes the space between shifts
too much bigger and difficult for gear shifting
then you need fine adjustment.
——Check the 1
st
shift position, loosen nut B, do as
the chart show: Put transmission on 1
st
shift
position, fasten bolt B by adjusting the
eccentric ring position to a=1.5mm.
— — Fasten clamp bolt (the transmission on the
neutral position), try all the shifts, which should
be smooth and easy.
——Try all the shifts gear shifting should be smooth
and without stop, secure the validity of the
reverse gear lockup.
Bolt
Eccentric Ring
J-11
TRANSMISSION RESOLUTION
1. Fastening Screw (4 Pieces, Fasten Moment Is25n.M) 2. Fixing Screw (2 Pieces, Fasten
Moment Is 25N.M) 3. Bleed Bolt 4. Transmission Rear Housing 5. 5
th
Synchronizer
Assembly 6. 5
th
Driven Gear Snap Ring 7. 5
th
Driven Gear 8. 5
th
Fork Pad
9. 5
th
Fork Assembly 10. 5
th
Gear Holder Fixing Turnbuckle 11. Dish Washer 12. Shim
J-12
1. Input Shaft Rear Bearing Plate Screw (4 Pieces, Fasten Moment Is 15N.M) 2. Transmission
Housing Assembly 3. Fixing Screw (12 Pieces, Fasten Moment Is 25N.M) 4. O-Ring 5. Gearshift
Shaft Plug Cover 6. Gearshift Shaft Pressing Spring 7. Gearshift Assembly 8. Gearshift Positioning
Holder Assembly 9. Pressing Spring-Damper Ring 10. Output Flange 11. Output Flange Dish Washer
12. Output Flange Snap Ring 13. Flange Cover 14. Idler Shaft Fixing Screw 15. Fixing Bolt (2
Pieces, Fasten Moment Is 25N.M)
J-13
1. 4
th
Driven Gear Snap Ring 2. 4
th
Driven Gear 3. 3
rd
Driven Snap Ring 4. 3
rd
Driven Gear 5.
2
nd
Driven Gear 6. 2
nd
Synchronizer Ring 7. 2
nd
Roller Bearing 8. 2
nd
Roller Bearing Lining 9.
1
st
-2
nd
Synchronizer Assembly 10. 1
st
Synchronizer Ring 11. 1
st
Driven Gear 12. 1
st
Roller
Bearing 13. Bearing Holder Fixing Bolt 14. 1
st
Roller Bearing Snap Ring 15. Output Shaft
Intermediate Bearing Holder 16. Differential Assembly 17. Damper Ring 18. Pressing
Spring-Damper Ring 19. Output Flange 20. Output Flange Dish Washer 21. Output Flange Snap
Ring 22. Output Flange Cover 23. Fork 24. 5
th
Fork Sleeve 25. 3
rd
-4
th
Fork 26. 5
th
Fork Guide
Plate 27. Reverse Fork Guide Plate 28. 1
st
-2
nd
Fork 29. Input Shaft Assembly 30. Idler Shaft
31. Idler Assembly 32. Clutch Housing assembly
J-14
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст