Chery A15. Manual — part 164
Chery A15 Maintenance Manual
Circuit diagram of Chery A15 windshield wiper and washer:
Circuit Diagram of Windshield Wiper and Washer
到喇叭继电器
To horn relay
红
Red
间歇雨刮继电器
Intermittent wiper relay
绿
Green
洗涤器
Washer
棕
Brown
喇叭按钮
Horn
button
黑
Black
雨刮器开关
Wiper
switch
黄
Yellow
雨刮电机
Wiper
motor
兰
Blue
灰
Gray
Chery A15 Maintenance Manual
Wiper/Washer Component Part Function List
Level
Switch
Intermittent
Relay
(Conduction
between Pins)
V5 Washer
(Conduction
between Pins)
Wiper Switch
(Conduction
between Pins)
Wiper Motor
(Conduction
between Pins)
Remarks
Low speed
5/53s
2/53m
B+
53e
53
B+
53
B+
B+
(Power
supply
anode)
High speed
53b
53a
B+
53b
B+
B+
(Power
supply
anode)
Intermittent
1/J
2/53m
B+
8/15
int
53a
B+
53
B+
B+
(Power
supply
anode)
Returning
5/53s
2/53m
B+
53
53e
B+
53
53e
53a
B+
B+
(Power
supply
anode)
Washing
6/T
2/53m
8/15
B+
1
B+
53a
53c
B+
53
B+
B+
(Power
supply
anode)
Chery A15 Maintenance Manual
Section Two: Installation of Wiper/Washer System
1. Installing Wiper
Assemble wiper blade and swing bar;
Open engine hood;
Insert wiper connecting rod to make fixing hole and the welding nut on vehicle
body concentric;
Fasten the connecting rod with three bolts and washers, tightening torque:
9Nm;
Install downflow trough flapper of windshield, etc. (refer to vehicle body
instruction);
Align wiper blade with the arrow stamped on windshield; fix swing bar in
swing bar shaft and tighten fixing nut, meanwhile keep pressing wiper blade to
avoid movement;
Fasten swing bar with two nuts, tightening torque: 16-19Nm, and then fit
protective cover.
2. Installing Washer System
Fix six cleaning fluid pipe fixing clips and one jecket;
Fix nozzles on engine hood;
Connect one end of cleaning fluid pipe with fluid tank, and fix cleaning fluid
pipe in correct direction, then fix nozzle connector;
Lock cleaning fluid tank onto vehicle body properly, and tighten with one nut
and washer.
Chery A15 Maintenance Manual
Section Three: Troubleshooting
Component Symptom Possible Cause
Solution
Remarks
Wiper motor
After ignition
switch is turned
on, wiper motor
does not work
when wiper
switch is at all
positions
(intermittent
wiping, low-speed
wiping,
high-speed wiping
and short-term
wiping).
(1) Wiper motor
power supply
open circuit.
(2) Poor contact
of ignition switch
or wiper switch.
(3) Wiper motor
open circuit.
(1) Check wiper power
supply for open circuit and
eliminate it if any.
(2) Measure voltage value
at each point on motor
winding with a multimeter
to check for open circuit,
and replace motor if any.
(3) Check wiper switch and
unloading relay at contact
X, and replace the parts if
abnormity is found.
Wiper motor
After ignition
switch is turned
on, wiper motor
has no intermittent
service when
wiper switch is
placed at
(intermittent
wiping) position.
(1) Wiper
intermitter open
circuit.
(2) Internal
breakdown of
wiper intermitter.
(1) Check fuse S8 on relay
box, wiper relay and
unloading relay of contact
8/15.
(2) If fuse and relay are all
normal, check wiper
intermitter for open circuit.
Wire transfer route: ignition
switch ON - terminal 5F/2
of wiper motor -
intermittent level switch on
- 5F/5 - intermitter relay 1/J
- intermitter relay activated
Fuse S8 → wiper relay
terminal 8/15 → wiper
relay terminal 2/53M →
hole 2 of relay board plug S
wiper motor → green wire
→
wiper motor terminal
4/53 → wiper motor
terminal 5/31 →
brown/yellow wire →
earthing.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст