Chery A15. Manual — part 163
Chery A15 Maintenance Manual
on when
vehicle is
running
pressure switch.
(3) High pressure
switch (180kPa
switch) fault.
(4) Open circuit of
high pressure switch.
(5) Lubrication duct
pressure meets no
specified value.
pressure.
(1) Connect a diode test lamp
between battery anode and low
pressure switch, and the lamp is
lighted. Start engine and increase
engine speed slowly, the diode test
lamp shall go out when pressure
reaches 15-45KPa. If the lamp
does not go out, the low pressure
switch might be at fault; idle run
the engine, engine oil pressure
shall be higher than 45KPa and
the test lamp shall go out. Any oil
pressure lower than 15kPa
indicates lubrication system fault.
(2) Connect diode test lamp with
high pressure switch and increase
engine speed slowly. When engine
oil pressure reaches 160- 200KPa,
test lamp shall go on. If not on,
high pressure switch probably is
at fault. Further increase engine
speed to 2000r/min, the oil
pressure shall at least reach
200kpa. If not, the lubrication
system is at fault.
If the problem still exists after
lubrication system and pressure
switches are all found normal in
the above inspection, then check
circuit for failure according to
circuit diagram.
Note: low pressure switch
warning light goes on when the
circuit is earthed, so earthed
circuit is the key point when
checking; while high pressure
warning light goes on when the
Chery A15 Maintenance Manual
circuit is open or engine speed
exceeds 2000r/min, therefore
checking for open circuit is of
greatest importance.
Coolant
warning
light
Coolant
warning
light keeps
on when
vehicle is
running in
both cold
state and hot
state
(1) Low level in
coolant tank.
(2) Coolant level
switch fault.
(3) Coolant
temperature warning
switch fault.
(4) Warning light
circuit earthed.
(1) Check enginge coolant to see
if the temperature is too high or
the level is too low.
(2) If the above is normal, unplug
coolant tank level switch. If
warning light goes out, the level
switch is at fault.
(3) If the warning light keeps on,
plug level switch and unplug
coolant temperature warning
switch. If the warning light goes
out, the coolant temperature
warning switch is at fault; and if
the light keeps on, the circuit is
probably earthed.
Brake
warning
light
Brake
warning
light keeps
on when
parking
brake lever
is released.
(1) Brake fluid level
too low.
(2) Brake fluid level
switch fault.
(3) Parking brake
switch fault.
(4) Warning light
circuit problem.
(1) Check brake fluid to see if the
level is too low.
(2) If brake fluid level is normal,
unplug brake fluid level switch. If
warning light goes out, brake fluid
level switch is at fault.
(3) If warning light keeps on,
unplug parking brake switch. If
warning light goes out, parking
brake switch is at fault; and if
warning light still keeps on, the
circuit is earthed somewhere.
Chery A15 Maintenance Manual
Chapter Six: Electric Wiper and Windshield Washer
Section One: Introduction to Wiper/Washer System
Wiper mainly consists of motor assembly, trilink mechanism, swing bar with three
direction ball knots and wiper blade. See figure (Wiper-1) for wiper and figure
(Wiper-2) for motor.
Wiper (Wiper-1)
1-Permanent DC motor
2-Gear worm reducer
3-Wiper motor output shaft
Wiper Motor (Wiper-2)
Wiper motor includes a PM DC small size motor and a gear worm reducer. In order to
ensure that wiper swing bar and wiper blade will stop at the lower edge of windshield
and remain parallel to it after working, an autostop positioning conducting strip is
installed on the back side of reducer worm wheel output shaft, and three contacts
Chery A15 Maintenance Manual
connecting to conducting strip are located on reducer rear cover. They work together,
with the help of contact at zero position of the wiper switch, to provide the autostop
positioning function of wiper.
Washer includes a mini PM DC motor, a centrifugal water pump, nozzles, fluid tank
and water pipe. Motor and water pump together compose a washer motor and water
pump assembly, as shown in the figure (Wiper-6):
1-Water inlet
2-Impeller
3-Pump
4-Water outlet
5-PM DC motor
Washer Motor (Wiper-3)
This assembly is fixed on fluid tank and forms a washer assembly with the tank, as the
figure (Wiper-6) shows. Washer assembly is installed on left wing, and the volume of
fluid tank is 5.lL.
Washer motor
Washer Assembly (Wiper-4)
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст