Chery A11. Manual — part 135
Chery SQR7160 series sedan ABS system-fault diagnostic and repairing
) to each wheel cylinder. Plug ports immediately.
* Remove screw cap holding HECU on the carrier.
rrier.
trolled Unit
* Press locking buckle at connector side, and remove
on ECU.
g new screw. Tighten torque:
.
acing ECU
* Press locking buckle at connector side, and remove
rom ECU.
ew screws. Tighten torque is:
lic port cannot be
moved until brake fluid pipe is ready for installing. Avoid
install brake pipe.
torque is 12+4Nm (M10×1)
* Remove and mark brake fluid pipe (1-4
* Remove HECU assembly from ca
14.4 Replacing Hydraulic Con
pump motor wiring harness.
* Remove 4 screws shown on illustration. Removed screws
cannot be reused.
* Separate HCU and ECU.
* Install a new HCU
* Retain ECU on HCU usin
3+1Nm。
* Connect motor wiring harness. Locking buckle must be
well settled
14.5 Repl
wiring harnesss.
* Remove 4 screws shown on illustration 4 and discard.
* Remove HCU f
* Install a new ECU on HCU.
* Lock ECU on HCU using n
3+1Nm
Connect motor wiring harness and settle locking buckle well.
14.6 Installing ABS assembly
Note:Plug on ABS assembly hydrau
re
foreign material entering brake system.
* Install ABS assembly on carrier. Tighten torque is 20+4Nm
* Remove plug at hydaulic ports and
Ensure pipe connect correctly.
* Install brake pipe to master pump.
* Brake pipe mounting tighten
28
specified method.
k can be felt).
15.ECU Programming
New ECU should be programmed when replacing HECU or ECU. Otherwise ABS warning light will flash and
rogramme ECU using scan tool by following methods:
and 15+3Nm(M12×1).
* Fill new brake fluid to fluid reservoir until fluid level reaches MAX, and bleeding as
* Turn ignition to ON position, ABS warning light should go on 1.7 second and then off.
* Clear fault code memory, and retrive again. Ensure no codes in memory.
* Finally perform vehicle drive test to confirm ABS function correctly (pedal kic
system doe not operate.
P
Connect scan tool to diagnostic socket
Enter 03 at
press Q key.
ADDRESS,
Enter 07 at FUNCTION SELECT, press Q key.
Enter approciate code 01901 (see ABS electrical circuit) at CODE INPUT.
Display code being entered, press
Enter 06 at FUNCTION SELECT, press Q key.
END
Chery SQR7160 series sedan ABS system-fault diagnostic and repairing
29
Chery SQR7160 series sedan ABS system-fault diagnostic and repairing
16. Filling brake fluid and bleeding
16.1 Oil Carried HCU
If spare part is an oile carried HCU, after replacing, fill and bleed HCU using conventional brake system methods.
16.2 Dry HECU
If spare HECU is a dry one, after replacing, HECU second circuit must be bleeded after filling and bleeding as per
conventional brake system. Operating procedures are as following using scan tool:
Filling and bleeding as per conventional brake system
procedures until no bubbles in transparent pipes.
Connect scan tool to diagnostic connector
Enter 03 at ADDRESS, press Q key.
Enter 04 at FUNCTION SELECT, press Q key.
Enter 001 at GROUP NUMBER, press Q key.
To next page
30
From previous page.
Depress brake pedal and keep depressed, hydraulic
pump operates and pedal kick back.
Depress brake pedal 10 times, tighten left and right front
brake caliper bleed screw, press key.
Loosen brake pedal, and loosen left and right front brake
caliper bleed screw, press key.
Repeat above procedures 7 times.
BLEEDING OVER displayed, press
key to return to FUNCTION SELECT menu.
Enter 06 at FUNCTION SELECT, press Q key.
END
31
Chery SQR7160 series sedan ABS system-fault diagnostic and repairing
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст