Chery SQR 7160 sedan. Manual — part 9

specified method.

k can be felt).

15.ECU Programming

New ECU should be programmed when replacing HECU or ECU. Otherwise ABS warning light will flash and

rogramme ECU using scan tool by following methods:

and 15+3Nm(M12×１).

* Fill new brake fluid to fluid reservoir until fluid level reaches MAX, and bleeding as

* Turn ignition to ON position, ABS warning light should go on 1.7 second and then off.

* Clear fault code memory, and retrive again. Ensure no codes in memory.

* Finally perform vehicle drive test to confirm ABS function correctly (pedal kic

system doe not operate.

P

Connect scan tool to diagnostic socket

Enter 03 at

press Q key.

ADDRESS,

Enter 07 at FUNCTION SELECT, press Q key.

Enter approciate code 01901 (see ABS electrical circuit) at CODE INPUT.

Display code being entered, press

Enter 06 at FUNCTION SELECT, press Q key.

END

16. Filling brake fluid and bleeding

16.1 Oil Carried HCU

If spare part is an oile carried HCU, after replacing, fill and bleed HCU using conventional brake system methods.

16.2 Dry HECU

If spare HECU is a dry one, after replacing, HECU second circuit must be bleeded after filling and bleeding as per

conventional brake system. Operating procedures are as following using scan tool:

Filling and bleeding as per conventional brake system

procedures until no bubbles in transparent pipes.

Connect scan tool to diagnostic connector

Enter 03 at ADDRESS, press Q key.

Enter 04 at FUNCTION SELECT, press Q key.

Enter 001 at GROUP NUMBER, press Q key.

To next page

30

From previous page.

Depress brake pedal and keep depressed, hydraulic

pump operates and pedal kick back.

Depress brake pedal 10 times, tighten left and right front

brake caliper bleed screw, press key.

Loosen brake pedal, and loosen left and right front brake

caliper bleed screw, press key.

Repeat above procedures 7 times.

BLEEDING OVER displayed, press

key to return to FUNCTION SELECT menu.

Enter 06 at FUNCTION SELECT, press Q key.

END

31

Attachment I

ABS FAQ

●What is ABS?

ABS is abbreviation of Anti-Lock System. ABS ensures to maintain good braking stability and cornering while

keeping optimum braking distance on various road surfarces.

●Why use ABS?

During braking, vehicle will lose steering ability when front wheel lock and vehicle will slid when rear wheel block.

ABS will ensure your control to vehicle when braking by preventing wheel from blocking. With ABS function, driver can

bypass obstacles on way.

How to tell if an ABS installed?

Two methods recommended：

Firstly, check if there is a short lighting ABS warning light on instruments panel or switches panel;

Secondly, consult from the dealer.

● How ABS operate?

Upon wheel speed sensor signal and certain control logic, ABS ECU controls each wheel brake channel pressure

through solenoid valve repeatedly regulating.

●How to tell if ABS is operating?

When ABS operating, brake pedal vibrating will be felt and ECU operating sound will be heard

Warning: DO NOT be afraid at this moment, DPRESSED brake pedal firmly and keep pedal depressed.

● Is an ABS installed vehicle braking distance shorter than a vehicle without ABS?

In most cases, YES, especially on an icy, snowy or a wet road surface. DO NOT forget to turn steering wheel to

bypass obstacles on way even under crucial circumstances.

●How if ABS fail?

If ABS fails, ABS warning light will be on steadily，ABS will not work but conventional brake still operates. You may

brake as per conventional braking method.

When ABS warning light turns on?

ABS warning light goes on for 1.7 second and then off after engine on. During driving, ABS will not go on until ABS

fails. Therefore, the fault must be repaired as soon as possible once ABS warning light goes on during normal driving

condition. We recommend you to repair the fault at vehicle service shop and do not try to repair ABS by yourself.

32