Jaguar X-Type Sedan and Estate (Wagon). Manual — part 534
6. Connect the generator electrical connector.
7. Attach the generator positive cable.
Tighten to 12 Nm.
8. Install the generator cooling duct to the generator.
Tighten to 4 Nm.
9. Using the special tool, attach the accessory drive belt.
10. Attach the right-hand stabilizer bar link.
Attach the ABS wiring harness mounting bracket.
Tighten to 48 Nm.
11. Install the tie-rod end and the tie-rod end retaining nut.
Tighten to 35 Nm.
12. Install the right-hand wheel arch liner access cover.
13. Install the front, right-hand wheel and tire.
For additional information, refer to:
Wheel and Tire
(204-04 Wheels and
Tires, Removal and Installation).
14. Install the air deflector.
For additional information, refer to:
Air Deflector - 2.0L Duratorq-
TDCi/2.2L Duratorq-TDCi (110kW /150PS) - Puma
(501-02 Front End Body
Panels, Removal and Installation).
15. Connect the battery ground cable.
For additional information, refer to:
Battery Connect
(414-01 Battery,
Mounting and Cables, General Procedures).
Published: 11-May-2011
Information and Entertainment System - General Information - Audio System
Diagnosis and Testing
Principle of Operation
For a detailed description of the Audio System and components, refer to the relevant Description and Operation section in the workshop
manual. REFER to:
Audio System
(415-01 Audio Unit, Description and Operation),
Antenna
(415-02 Antenna, Description and Operation),
Speakers
(415-03 Speakers, Description and Operation).
Inspection and Verification
1. Verify the customer concern.
1.
2. Visually inspect for obvious signs of mechanical or electrical damage.
2.
• NOTE: Before any testing of the 'audio sound quality' make sure that the cassette tape mechanism is cleaned using the Jaguar cleaning
tape. Any testing material (tape, CD, radio, mini disc) should be of known 'good quality'. Avoid using tapes that are old, home recordings, or
damaged. Avoid using compact discs that are scratched, dirty, CDR's or CDRW 's. Avoid using radio stations that are in the AM band, weak
signal strength, inside buildings or poor reception areas. Use a good sound source for testing.
Mechanical
Electrical
Cassette tape mechanism cleanliness
Compact disc cleanliness
Mini disc cleanliness
Fuse(s)
Wiring Harness For Damage And Corrosion
Electrical Connector(s) Loose, Damaged Or Corrosion
3. If an obvious cause for an observed or reported concern is found, correct the cause (if possible) before proceeding to the next
step.
3.
• NOTE: If a new audio unit is being installed under warranty, please supply the digital data bus (D2B) ring configuration and the
diagnostic trouble code(s) with the returned unit to aid fault replication.
4. If the cause is not visually evident, verify the symptom and refer to the Jaguar approved diagnostic system.
4.
DTC Index
Gateway module
CAUTION: W hen probing connectors to take measurements in the course of the pinpoint tests, use the adaptor kit, part number
3548-1358-00
• NOTE: If the control module/component is suspect and the vehicle remains under manufacturer warranty, refer to the Warranty Policy and
Procedures manual (section B1.2), or determine if any prior approval program is in operation, prior to the installation of a new
module/component.
• NOTE: When performing voltage or resistance tests, always use a digital multi meter (DMM) accurate to three decimal places and with a
current calibration certificate. When testing resistance, always take the resistance of the DMM leads into account.
• NOTE: Check and rectify basic faults before beginning diagnostic routines that involve pinpoint tests.
• NOTE: Inspect connectors for signs of water ingress, and pins for damage and/or corrosion.
• NOTE: If DTCs are recorded and, after performing the pinpoint tests, a fault is not present, an intermittent concern may be the cause.
Always check for loose connections and corroded terminals.
DTC
Description
Possible Causes
Action
B11A4 DAB L Band Antenna
Gateway module (digital audio
broadcast band L band) antenna
circuit - short to power, ground
or open circuit
Carry out any pinpoint tests associated with this DTC using
the manufacturer approved diagnostic system. Refer to
electrical circuit diagrams, notes and check (digital audio
broadcast L band) antenna circuit for short to power, ground or
open circuit
B11A5 DAB Band 3 Antenna
Gateway module (digital audio
broadcast band 3) antenna
circuit - short to power, ground
or open circuit
Carry out any pinpoint tests associated with this DTC using
the manufacturer approved diagnostic system. Refer to
electrical circuit diagrams, notes and check (digital audio
broadcast band 3) antenna circuit for short to power, ground or
open circuit
B1238 High Temperature
Gateway module - over
temperature
Check gateway module and location for causes of excessive
temperature, install a new gateway module as required, refer
to the new module installation note at the top of the DTC
Index
B1342 Internal failure in Gateway
module
Gateway module - internal
failure
Internal failure install a new gateway module as required,
refer to the new module installation note at the top of the
DTC Index
B1A89 SDARS or Digital Tuner
Antenna
Gateway module satellite radio
module or digital tuner antenna
circuit - short to power, ground
or open circuit
Carry out any pinpoint tests associated with this DTC using
the manufacturer approved diagnostic system. Refer to
electrical circuit diagrams, notes and check satellite radio
module or digital tuner antenna circuit for short to power,
ground or open circuit
B2477 Module Configuration Failure
Gateway module - configuration
failure
The module can be configured using the new module
procedure. Check and configure as required
U0193 Lost Communication with
Digital Audio Control Module
A Satellite Radio Module
Gateway module - lost
communication with satellite
radio module
Carry out any pinpoint tests associated with this DTC using
the manufacturer approved diagnostic system. Refer to
electrical circuit diagrams, notes and check satellite radio
module power and bus circuit to gateway module on MOST ring
DTC
Description
Possible Causes
Action
U0194 Lost Communication with
Digital Audio Control Module
B Digital Audio Broadcast
Module
Gateway module - lost
communication with digital
audio broadcast module
Carry out any pinpoint tests associated with this DTC using
the manufacturer approved diagnostic system. Refer to
electrical circuit diagrams, notes and check digital audio
broadcast module power and bus circuit to gateway module on
MOST ring
U0237 Lost Communication with
Digital Audio Control Module
C IBOC In Band On Channel /
HD Radio
Gateway module - lost
communication with Digital
Audio Control Module C
Carry out any pinpoint tests associated with this DTC using
the manufacturer approved diagnostic system. Refer to
electrical circuit diagrams, notes and check Digital Audio
Control Module C power and bus circuit to gateway module on
MOST ring
U1A15 Incomplete MOST Ring
Reported By ICM
Gateway module - (MOST) ring
break
Carry out any pinpoint tests associated with this DTC using
the manufacturer approved diagnostic system. Refer to
electrical circuit diagrams, notes and check (MOST) circuit for
ring break
U2601 (D2B)Wake-up Line Short to
Ground
Gateway module - wake-up line
short to ground
Carry out any pinpoint tests associated with this DTC using
the manufacturer approved diagnostic system. Refer to
electrical circuit diagrams, notes and check gateway module
(D2B) wake-up line for short to ground
U2609 (D2B)Wake-up pulse width
out of spec
Gateway module - wake-up line
fault (pulse< 50mS, pulse >
110mS)
Refer to electrical circuit diagrams, notes and check gateway
module (D2B) wake-up line circuit for fault
U2610 (D2B) Slave ECU fails to
receive a report position
Gateway module - during
initialization no position status
report is received from one or
more slave modules
Refer to electrical circuit diagrams, notes and check (D2B)
slave modules and circuit for fault, replace as required, refer to
the new module installation note at the top of the DTC Index
U2611 (D2B) Slave ECU fails to
receive an alarm clear
command
Gateway module - on entering
alarm state, slave ECU has
failed to receive alarm clear
command
Refer to electrical circuit diagrams, notes and check (D2B)
slave modules and circuit for fault, replace as required, refer to
the new module installation note at the top of the DTC Index
U3004 Digital Tuner (Most slave)
Internal fault
Gateway module - digital tuner
MOST slave module is
inoperative
Refer to electrical circuit diagrams, notes and check digital
tuner module replace as required, refer to the new
module/component installation note at the top of the DTC
Index
U3098 Digital Tuner (Most slave)
Over temperature
Gateway module - digital tuner
(Most slave) is hot
Check digital tuner module and location for causes of
excessive temperature, install a new module as required, refer
to the new module installation note at the top of the DTC
Index
Radio Head Unit
CAUTION: W hen probing connectors to take measurements in the course of the pinpoint tests, use the adaptor kit, part number
3548-1358-00
• NOTE: If the control module/component is suspect and the vehicle remains under manufacturer warranty, refer to the Warranty Policy and
Procedures manual (section B1.2), or determine if any prior approval program is in operation, prior to the installation of a new
module/component.
• NOTE: When performing voltage or resistance tests, always use a digital multimeter (DMM) accurate to three decimal places and with a
current calibration certificate. When testing resistance, always take the resistance of the DMM leads into account.
• NOTE: Check and rectify basic faults before beginning diagnostic routines that involve pinpoint tests.
• NOTE: Inspect connectors for signs of water ingress, and pins for damage and/or corrosion.
• NOTE: If DTCs are recorded and, after performing the pinpoint tests, a fault is not present, an intermittent concern may be the cause.
Always check for loose connections and corroded terminals.
DTC
Description
Possible Causes
Action
B1238 Over Temperature
Fault
Radio head unit, CD
multichanger - overheated
(+80 degrees Celsius)
Check cd multichanger module and location for causes of excessive
temperature, install a new module as required, refer to the new module
installation note at the top of the DTC Index
B1342 ECU Internal Failure
Radio head unit - no radio
function
Refer to electrical circuit diagrams, notes and check Radio head unit radio
functions for fault, replace as required, refer to the new module
installation note at the top of the DTC Index
B2004 Internal Media Over
Temperature Fault
Radio head unit - internal
cd/md has overheated
Check Radio head unit and location for causes of excessive temperature,
install a new module as required, refer to the new module installation
note at the top of the DTC Index
B2401 Audio Tape Deck
Mechanism Fault
Radio head unit - tape
loading, tape eject, tape
stuck, tape cut and seek
stop error
Refer to electrical circuit diagrams, check radio head unit install a new
module as required, refer to the new module installation note at the top
of the DTC Index
B2403 Audio CD/DJ Internal
Fault
Radio head unit, CD
multichanger module - cd
eject error, cd loading error
Refer to electrical circuit diagrams, notes and check cd multichanger
module install a new module as required, refer to the new module
installation note at the top of the DTC Index
B2477 Module Configuration
Failure
Radio head unit -
configuration failure
The module can be configured using the new module procedure. Check
and configure as required
B2888 Audio Headunit Media
Fault
Radio head unit - tape
loading, tape eject, tape
stuck, tape cut and seek
stop error
Check radio head unit install a new module as required, refer to the new
module installation note at the top of the DTC Index
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст