Jaguar XJ (X350). Manual — part 1012
PINPOINT TEST G549822p14 :
CRANKSHAFT POSITION (CKP)
SENSOR
G549822t182 : CHECK THE CKP CIRCUITS FOR SHORT CIRCUIT TO GROUND
1.
Circuit
Pin
Crankshaft position sensor - signal
02
Crankshaft position sensor - positive
01
Crankshaft position sensor - negative 03
2.
Circuit
Pin
Crankshaft position sensor - signal
F1
Crankshaft position sensor - positive
G1
Crankshaft position sensor - negative G2
3. Key off. 4. Disconnect the ECM connector, C101. 5. Key on, engine off. 6. Measure the resistance
between:
C101, harness side
Battery
Pin G2
Negative terminal
Pin G1
Negative terminal
Pin F1
Negative terminal
Are the resistances greater than 100 Kohms?
-> Yes
GO to Pinpoint Test G549822t183.
-> No
REPAIR the short circuit to ground in the CKP harness or component. For additional information,
refer to the wiring diagrams. Clear any DTCs, test the system for normal operation.
G549822t183 : CHECK THE CKP CIRCUITS FOR SHORT CIRCUIT TO POWER
1. Measure the resistance between:
C101, harness side
Battery
Pin G2
Positive terminal
Pin G1
Positive terminal
Pin F1
Positive terminal
Are the resistances greater than 100 Kohms?
-> Yes
GO to Pinpoint Test G549822t184.
-> No
REPAIR the short circuit to ground in the CKP harness or component. For additional information,
refer to the wiring diagrams. Clear any DTCs, test the system for normal operation.
www.
G549822t184 : CHECK THE CKP CIRCUIT RESISTANCE
1. Measure the resistance between:
C101, harness side C101, harness side
Pin G2
Pin F1
Is the resistance between 100 - 120 Kohms?
-> Yes
GO to Pinpoint Test G549822t185.
-> No
REPAIR the out of limits resistance in the CKP harness or component. This may be due to a short or
open circuit, depending on the result of the last measurement. For additional information, refer to
the wiring diagrams. Clear any DTCs, test the system for normal operation.
G549822t185 : CHECK THE CKP CIRCUIT RESISTANCE
1. Measure the resistance between:
C101, harness side C101, harness side
Pin G1
Pin F1
Pin G1
Pin G2
Are the resistances greater than 100 Kohms?
-> Yes
An intermittent fault may be present in the wiring harness. Visually check for chaffed wires or other
physical damage to the harness. If no fault is found in the circuit, suspect the following
component(s): - Open circuit in sensor power line - CKP connector - CKP sensor - Crankshaft sensor
target wheel - ECM connector - ECM
-> No
REPAIR the out of limits resistance in the CKP harness or component. This may be due to a short or
open circuit, depending on the result of the last measurement. For additional information, refer to
the wiring diagrams. Clear any DTCs, test the system for normal operation.
PINPOINT TEST G549822p15 :
CAMSHAFT POSITION (CMP) SENSOR
G549822t186 : CHECK THE CMP CIRCUITS FOR SHORT CIRCUIT TO GROUND
1.
Circuit
Pin
Camshaft position sensor - signal
01
Camshaft position sensor - return 02
Camshaft position sensor - power 03
2.
Circuit
Pin
Camshaft position sensor - signal
G4
Camshaft position sensor - return H3
Camshaft position sensor - power H4
3. Key off. 4. Disconnect the ECM connector, C101. 5. Key on, engine off. 6. Measure the resistance
between:
www.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст