Jaguar XJ (X350). Manual — part 1011

-> Yes

Suspect: - ECM connector - ECM

-> No

REPAIR the high resistance circuit. For additional information, refer to the wiring diagrams. Clear any

DTCs, test the system for normal operation.

G549822t173 : CHECK FOR POWER TO THE ACT SENSOR

1. Measure the voltage between:

C69, harness side

Battery

Pin 01

Negative terminal

Is the voltage between 4.8 - 5.2 volts?

-> Yes

GO to Pinpoint Test G549822t177.

-> No

GO to Pinpoint Test G549822t174.

G549822t174 : CHECK THE ACT SIGNAL CIRCUIT FOR SHORT CIRCUIT TO
GROUND

1. Measure the resistance between:

C69, harness side

Battery

Pin 01

Negative terminal

Is the resistance greater than 100 Kohms?

-> Yes

GO to Pinpoint Test G549822t175.

-> No

GO to Pinpoint Test G549822t178.

G549822t175 : CHECK THE ACT SIGNAL CIRCUIT FOR SHORT CIRCUIT TO
POWER

1. Key on, engine off. 2. Measure the resistance between:

C69, harness side

Battery

Pin 01

Positive terminal

Is the resistance greater than 100 Kohms?

-> Yes

GO to Pinpoint Test G549822t176.

-> No

GO to Pinpoint Test G549822t181.

G549822t176 : CHECK THE ACT SIGNAL CIRCUIT FOR HIGH RESISTANCE

1. Key off. 2. Disconnect the ECM connector, C101. 3. Measure the resistance between:

C69, harness side C101, harness side

Pin 01

Pin B1

Is the resistance less than 10 ohms?

-> Yes

Suspect: - ECM connector - ECM

-> No

REPAIR the high resistance circuit. For additional information, refer to the wiring diagrams. Clear any

DTCs, test the system for normal operation.

G549822t177 : CHECK THE COMPONENT RESISTANCE

1. Measure the resistance between:

C69, component side C69, component side

Pin 01

Pin 02

www.

Is the resistance between 1 - 100 Kohms?

-> Yes

An intermittent fault may be present in the wiring harness. Visually check for chaffed wires or other

physical damage to the harness. If no fault is found in the circuit, suspect the following

component(s): - ACT connector. - ACT sensor. - ECM connector. - ECM

-> No

INSTALL a new ACT sensor.

G549822t178 : CHECK THE ACT SIGNAL AND RETURN CIRCUITS FOR SHORT
CIRCUIT TO EACH OTHER

1. Key off. 2. Disconnect the ECM connector, C101. 3. Key on, engine off. 4. Measure the resistance

between:

C69, harness side C69, harness side

Pin 01

Pin 02

Is the resistance greater than 100 Kohms?

-> Yes

GO to Pinpoint Test G549822t179.

-> No

REPAIR the short circuit. For additional information, refer to the wiring diagrams. Clear any DTCs, test

the system for normal operation.

G549822t179 : CHECK WHETHER THE SHORT CIRCUIT TO GROUND IS IN
THE HARNESS OR THE MODULE

1. Key on, engine off. 2. Measure the resistance between:

C69, harness side

Battery

Pin 01

Negative terminal

Is the resistance greater than 100 Kohms?

-> Yes

Suspect: - ECM

-> No

REPAIR the short circuit. For additional information, refer to the wiring diagrams. Clear any DTCs, test

the system for normal operation.

G549822t180 : CHECK WHETHER THE SHORT CIRCUIT TO POWER IS IN THE
HARNESS OR THE MODULE

1. Key off. 2. Disconnect the ECM connector, C101. 3. Key on, engine off. 4. Measure the resistance

between:

C69, harness side

Battery

Pin 02

Positive terminal

Is the resistance greater than 100 Kohms?

-> Yes

Suspect: - ECM

-> No

REPAIR the short circuit. For additional information, refer to the wiring diagrams. Clear any DTCs, test

the system for normal operation.

G549822t181 : CHECK WHETHER THE SHORT CIRCUIT TO POWER IS IN THE
HARNESS OR THE MODULE

1. Key off. 2. Disconnect the ECM connector, C101. 3. Key on, engine off. 4. Measure the resistance

between:

C69, harness side

Battery

Pin 01

Positive terminal

Is the resistance greater than 100 Kohms?

-> Yes

Suspect: - ECM

-> No

REPAIR the short circuit. For additional information, refer to the wiring diagrams. Clear any DTCs, test

the system for normal operation.

www.