Jaguar XJ (X350). Manual — part 1116
REM connector CR73, harness side
Battery
Pin 02
Negative terminal
4. Measure the resistance between:
REM connector CR71, harness side
Battery
Pin 15
Negative terminal
Is either resistance greater than 5 ohms?
-> Yes
REPAIR the high resistance circuit. For additional information, refer to the wiring diagrams. CLEAR the
DTC, test the system for normal operation.
-> No
CHECK for DTCs indicating a REM or ECM fault. REFER to the DTC index.
Electronic Engine Controls - VIN Range: G45704->G99999 For vehicles with 3.0L engines and
Electronic Engine Controls - VIN Range: G45704->G99999 For vehicles with 3.5L and 4.2L engines.
PINPOINT TEST G532449p9 : FUEL
PUMP DRIVER MODULE (FPDM)
POWER AND GROUND CIRCUITS (V8
VEHICLES WITH SUPERCHARGER)
G532449t43 : CHECK THE POWER SUPPLY VOLTAGE TO THE FPDM
1. Disconnect the FPDM electrical connector, FP26. 2. Key on, engine off. 3. Make sure the fuel pump
relay is energized. 4. Measure the voltage between:
FPDM connector FP26, harness side
Battery
Pin 05
Negative terminal
Is the voltage less than 10 volts?
-> Yes
REPAIR the circuit between the battery and the FPDM. This circuit includes fuse 24 of the rear power
distribution box, the fuel pump relay and the mega fuses. For additional information, refer to the
wiring diagrams. CLEAR the DTC, test the system for normal operation.
-> No
GO to Pinpoint Test G532449t44.
G532449t44 : CHECK THE FPDM GROUND FOR HIGH RESISTANCE
1. Measure the resistance between:
FPDM connector FP26, harness side
Battery
Pin 06
Negative terminal
Is the resistance greater than 5 ohms?
-> Yes
REPAIR the high resistance circuit. For additional information, refer to the wiring diagrams. CLEAR the
DTC, test the system for normal operation.
-> No
CHECK for DTCs indicating a FPDM or ECM fault.
Electronic Engine Controls - VIN Range: G45704->G99999 For vehicles with 3.0L engines and
Electronic Engine Controls - VIN Range: G45704->G99999 For vehicles with 3.5L and 4.2L engines.
PINPOINT TEST G532449p3 : FUEL
LEVEL SENSOR(S) CIRCUIT
RANGE/PERFORMANCE
G532449t7 : CHECK THE SIGNAL CIRCUIT BETWEEN THE REM AND LEVEL
SENSOR A FOR SHORT CIRCUIT TO GROUND
1. Disconnect the fuel pump module electrical connector, FP06. 2. Measure the resistance between:
Fuel module connector FP06, harness side
Battery
Pin 12
Negative terminal
Is the resistance less than 10,000 ohms?
www.
-> Yes
REPAIR the short circuit. For additional information, refer to the wiring diagrams. CLEAR the DTC, test
the system for normal operation.
-> No
GO to Pinpoint Test G532449t8.
G532449t8 : CHECK THE SIGNAL CIRCUIT BETWEEN THE REM AND LEVEL
SENSOR A FOR SHORT CIRCUIT TO POWER
1. Measure the resistance between:
Fuel module connector FP06, harness side
Battery
Pin 12
Positive terminal
Is the resistance less than 10,000 ohms?
-> Yes
REPAIR the short circuit. For additional information, refer to the wiring diagrams. CLEAR the DTC, test
the system for normal operation.
-> No
GO to Pinpoint Test G532449t10.
G532449t10 : CHECK THE SIGNAL CIRCUIT BETWEEN THE REM AND LEVEL
SENSOR B FOR SHORT CIRCUIT TO GROUND
1. Measure the resistance between:
Fuel module connector FP06, harness side
Battery
Pin 14
Negative terminal
Is the resistance less than 10,000 ohms?
-> Yes
REPAIR the short circuit. For additional information, refer to the wiring diagrams. CLEAR the DTC, test
the system for normal operation.
-> No
GO to Pinpoint Test G532449t11.
G532449t11 : CHECK THE SIGNAL CIRCUIT BETWEEN THE REM AND LEVEL
SENSOR B FOR SHORT CIRCUIT TO POWER
1. Measure the resistance between:
Fuel module connector FP06, harness side
Battery
Pin 14
Positive terminal
Is the resistance less than 10,000 ohms?
-> Yes
REPAIR the short circuit. For additional information, refer to the wiring diagrams. CLEAR the DTC, test
the system for normal operation.
-> No
GO to Pinpoint Test G532449t13.
G532449t13 : CHECK THE SIGNAL RETURN CIRCUIT BETWEEN THE REM
AND LEVEL SENSORS FOR SHORT CIRCUIT TO GROUND
1. Measure the resistance between:
Fuel module connector FP06, harness side
Battery
Pin 13
Negative terminal
Is the resistance less than 10,000 ohms?
-> Yes
REPAIR the short circuit. For additional information, refer to the wiring diagrams. CLEAR the DTC, test
the system for normal operation.
-> No
GO to Pinpoint Test G532449t14.
G532449t14 : CHECK THE SIGNAL RETURN CIRCUIT BETWEEN THE REM
AND LEVEL SENSORS FOR SHORT CIRCUIT TO POWER
1. Measure the resistance between:
www.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст