Jaguar XJ (X350). Manual — part 776
EGR stepper connector, PI15
Battery
Pin 04
Negative terminal
Pin 01
Pin 06
Pin 03
Is the resistance less than 10,000 ohms?
-> Yes
REPAIR the short circuit. For additional information, refer to the wiring diagrams. CLEAR the DTCs
and test the system for normal operation.
-> No
GO to Pinpoint Test G528708t3.
G528708t3 : CHECK THE EGR STEPPER CONTROL CIRCUITS FOR SHORT
CIRCUIT TO POWER
1. Measure the resistance between:
EGR stepper connector, PI15
Battery
Pin 04
Positive terminal
Pin 01
Pin 06
Pin 03
Is the resistance less than 10,000 ohms?
-> Yes
REPAIR the short circuit. For additional information, refer to the wiring diagrams. CLEAR the DTCs
and test the system for normal operation.
-> No
GO to Pinpoint Test G528708t4.
G528708t4 : CHECK THE EGR STEPPER CONTROL CIRCUITS FOR HIGH
RESISTANCE
1. Key off. 2. Disconnect the ECM electrical connector, EC300. 3. Measure the resistance between:
EGR stepper connector, PI15 ECM connector, EC300
Pin 04
Pin 53
Pin 01
Pin 52
Pin 06
Pin 51
Pin 03
Pin 50
Is the resistance greater than 5 ohms?
-> Yes
REPAIR the high resistance circuit. For additional information, refer to the wiring diagrams. CLEAR the
DTC and test the system for normal operation.
-> No
INSTALL a new EGR valve.
Exhaust Gas Recirculation (EGR) Valve (17.45.01) CLEAR the DTC and test the system for normal
operation. Refer to the warranty policy and procedures manual if an ECM is suspect.
PINPOINT TEST G528708p2 : CHECK
THE SECONDARY AIR INJECTION
PUMP CIRCUITS
G528708t5 : CHECK THE SECONDARY AIR INJECTION PUMP RELAY SUPPLY
VOLTAGES
1. Key off. 2. Remove the secondary air injection pump relay. 3. Measure the voltage between:
Secondary air injection relay base
Battery
Pin 01
Negative terminal
www.
Pin 03
Is the voltage less than 10 volts?
-> Yes
REPAIR the circuit between the relay base and battery. This circuit includes in-line (fuse 2) and the
mega fuses. For additional information, refer to the wiring diagrams. CLEAR the DTC and test the
system for normal operation.
-> No
GO to Pinpoint Test G528708t10.
G528708t10 : CHECK THE SECONDARY AIR INJECTION RELAY TO PUMP
SUPPLY CIRCUIT FOR SHORT CIRCUIT TO GROUND
1. Disconnect the secondary air injection pump electrical connector, EC93. 2. Measure the resistance
between:
Secondary air injection relay base
Battery
Pin 05
Negative terminal
Is the resistance less than 10,000 ohms?
-> Yes
REPAIR the short circuit. For additional information, refer to the wiring diagrams. CLEAR the DTC and
test the system for normal operation.
-> No
GO to Pinpoint Test G528708t11.
G528708t11 : CHECK THE SECONDARY AIR INJECTION RELAY TO PUMP
SUPPLY CIRCUIT FOR SHORT CIRCUIT TO POWER
1. Measure the resistance between:
Secondary air injection relay base
Battery
Pin 05
Positive terminal
Is the resistance less than 10,000 ohms?
-> Yes
REPAIR the short circuit. For additional information, refer to the wiring diagrams. CLEAR the DTC and
test the system for normal operation.
-> No
GO to Pinpoint Test G528708t6.
G528708t6 : CHECK THE SECONDARY AIR INJECTION PUMP SIGNAL CIRCUIT
FOR SHORT CIRCUIT TO GROUND
1. Measure the resistance between:
Secondary air injection relay base
Battery
Pin 02
Negative terminal
Is the resistance less than 10,000 ohms?
-> Yes
REPAIR the short circuit. For additional information, refer to the wiring diagrams. CLEAR the DTC and
test the system for normal operation.
-> No
GO to Pinpoint Test G528708t7.
G528708t7 : CHECK THE SECONDARY AIR INJECTION PUMP SIGNAL CIRCUIT
FOR SHORT CIRCUIT TO POWER
1. Measure the resistance between:
Secondary air injection relay base
Battery
Pin 02
Positive terminal
Is the resistance less than 10,000 ohms?
-> Yes
REPAIR the short circuit. For additional information, refer to the wiring diagrams. CLEAR the DTC and
test the system for normal operation.
www.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст