Jaguar XJ (X350). Manual — part 252
•
Is the voltage between 9 and 15 volts?
-> Yes
GO to Pinpoint Test
G531322t12
.
-> No
REPAIR the supply circuit as necessary. This circuit includes fuse 01 of the front power distribution
box. For additional information, refer to the wiring diagrams. Clear the DTC, test the system for
normal operation.
G531322t12 : CHECK THE MODULE IGNITION SUPPLY
1. Key on, engine off. 2. Measure the voltage between:
EC030, harness side
Battery
Ignition supply, pin 08 Negative terminal
•
Is the voltage between 9 and 15 volts?
-> Yes
GO to Pinpoint Test
G531322t13
.
-> No
REPAIR the supply circuit as necessary. This circuit includes fuse 03 of the primary junction box. For
additional information, refer to the wiring diagrams. Clear the DTC, test the system for normal
operation.
G531322t13 : CHECK THE PUMP GROUND
1. Key off. 2. Measure the resistance between:
EC030, harness side
Battery
Pump ground, pin 47 Negative terminal
•
Is the resistance less than 10 ohms?
-> Yes
GO to Pinpoint Test
G531322t14
.
-> No
REPAIR the ground circuit as necessary. For additional information, refer to the wiring diagrams.
Clear the DTC, test the system for normal operation.
G531322t14 : CHECK THE VALVE GROUND
1. Measure the resistance between:
EC030, harness side
Battery
Valve ground, pin 16 Negative terminal
•
Is the resistance less than 10 ohms?
-> Yes
Refer to the warranty policy and procedures manual if a module is suspect.
-> No
REPAIR the ground circuit as necessary. For additional information, refer to the wiring diagrams.
Clear the DTC, test the system for normal operation.
PINPOINT TEST G531322p4 : LEFT
HAND FRONT WHEEL SPEED SENSOR
(WSS)
G531322t15 : CHECK THE WSS RETURN CIRCUIT FOR SHORT CIRCUIT TO
GROUND
1.
Circuit
Pin
WSS signal
01
WSS return 02
www.
2.
Circuit
Pin
Left hand front WSS signal
46
Left hand front WSS return 45
3. Key off. 4. Disconnect the WSS connector, EC044. 5. Disconnect the ABS module connector, EC030.
6. Key on, engine off. 7. Measure the resistance between:
EC044, harness side
Battery
Pin 02
Negative terminal
•
Is the resistance greater than 100 Kohms?
-> Yes
GO to Pinpoint Test
G531322t16
.
-> No
REPAIR the short circuit. For additional information, refer to the wiring diagrams. Clear the DTC, test
the system for normal operation by driving the vehicle at more than 20 kph (12.5 mph) for more than
3 minutes.
G531322t16 : CHECK THE WSS RETURN CIRCUIT FOR SHORT CIRCUIT TO
POWER
1. Measure the resistance between:
EC044, harness side
Battery
Pin 02
Positive terminal
•
Is the resistance greater than 100 Kohms?
-> Yes
GO to Pinpoint Test
G531322t17
.
-> No
REPAIR the short circuit. For additional information, refer to the wiring diagrams. Clear the DTC, test
the system for normal operation by driving the vehicle at more than 20 kph (12.5 mph) for more than
3 minutes.
G531322t17 : CHECK THE WSS RETURN CIRCUIT FOR HIGH RESISTANCE
1. Measure the resistance between:
EC044, harness side EC030, harness side
Pin 02
Pin 45
•
Is the resistance less than 10 ohms?
-> Yes
GO to Pinpoint Test
G531322t18
.
-> No
REPAIR the high resistance circuit. For additional information, refer to the wiring diagrams. Clear the
DTC, test the system for normal operation by driving the vehicle at more than 20 kph (12.5 mph) for
more than 3 minutes.
G531322t18 : CHECK THE WSS SIGNAL CIRCUIT FOR SHORT CIRCUIT TO
POWER
1. Measure the resistance between:
EC044, harness side
Battery
Pin 01
Positive terminal
•
Is the resistance greater than 100 Kohms?
-> Yes
GO to Pinpoint Test
G531322t19
.
www.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст