Range Rover Body Repair Manual — part 16
75
SUPPLEMENTARY RESTRAINT SYSTEM
NEW RANGE ROVER
12
PRECAUTIONS
9. Press both operating buttons to deploy airbag
module.
10. DO NOT return to airbag module for 30 minutes.
11. Using gloves and face mask, remove airbag
module from tool, place airbag module in plastic
bag and seal bag.
12. Wipe down tool with damp cloth.
13. Transport deployed airbag module to designated
area for incineration
NOTE: DO NOT transport airbag module in
the vehicle passenger compartment.
Passenger’s airbag module
1. Carry out deployment tool self test.
2. Remove airbag module from fascia.
See
Repair.
3. Position tool SMD 4082/6 in vice, ensuring that
vice jaws grip tool above bottom flange to
prevent possibility of tool being forced upwards
from vice. Tighten vice.
4. Position brackets SMD 4082/7 to tool; lightly
tighten bolts.
5. Secure airbag module to tool SMD 4082/6.
Ensure module is correctly secured using all
fixings.
SUPPLEMENTARY RESTRAINT SYSTEM
13
PRECAUTIONS
6. Ensure airbag module mounting brackets are
secure.
WARNING: Ensure tool SMD 4082/1 is not
connected to battery.
7. Connect flylead SMD 4082/5 to airbag module.
8. Connect flylead SMD 4082/5 to tool SMD
4082/1.
WARNING: Do not lean over module whilst
connecting.
9. Connect tool SMD 4082/1 to battery.
WARNING: Ensure all personnel are
standing at least 15 metres away from
module.
10. Press both operating buttons to deploy airbag
module.
11. DO NOT return to airbag module for 30 minutes.
12. Using gloves and face mask, remove airbag
module from tool, place airbag module in plastic
bag and seal bag.
13. Wipe down tool with damp cloth.
14. Transport deployed airbag module to designated
area for incineration
NOTE: DO NOT transport airbag module in
the vehicle passenger compartment.
SUPPLEMENTARY RESTRAINT SYSTEM
1
REPAIR
AIRBAG MODULE - PASSENGER SIDE
Service repair no - 76.73.69
WARNING: All the airbag system
components, including the wiring harness,
MUST be renewed after the airbags have
deployed.
Remove
1. Disconnect both battery terminals, disconnect
negative lead first.
2. Remove glove box assembly.
See CHASSIS
AND BODY, Repair.
3. Release and disconnect air bag module
multiplug.
4. Remove 4 bolts and washers (E-10 Torx Bit)
securing air bag module to fascia frame.
5. Carefully release and remove air bag module.
CAUTION: Store the airbag module
correctly.
See this section.
Refit
NOTE: If a new airbag module is being
fitted the serial numbers must be
recorded.
6. Carefully fit air bag module to fascia. Fit Torx
bolts, and washers.
7. Tighten bolts to
9 Nm. (7 lbf.ft)
8. Connect air bag module multiplug and secure to
location.
9. Fit glove box assembly.
See CHASSIS AND
BODY, Repair.
10. Connect battery terminals, fit battery cover and
secure with turnbuckles.
11. Check Supplementary Restraint System using
TestBook .
75
SUPPLEMENTARY RESTRAINT SYSTEM
NEW RANGE ROVER
2
REPAIR
SRS ECU
Service repair no - 76.73.72
Remove
WARNING: Always disconnect negative
lead from battery first. Disconnection of
positive lead with negative lead connected
risks short circuit and severe sparking through
accidental grounding of spanner. Personal injury
could result.
1. Disconnect both battery terminals.
2. Remove centre console.
See CHASSIS AND
BODY, Repair.
3. Lift rear of sound deadener pad from
transmission tunnel.
4. Disconnect SRS ECU multiplug.
5. Release 2 multiplugs from bracket.
6. Remove 2 bolts securing ECU to bracket.
Remove ECU.
Refit
7. Reverse removal procedure.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст