Range Rover Body Repair Manual — part 22
CHASSIS AND BODY
13
REPAIR
7. Disconnect 3 towing harness multiplugs.
8. Remove 2 mounting bolt covers.
9. Remove 2 bolts securing bumper to chassis.
10. With assistance, release bumper ends from
brackets. Remove bumper.
Refit
11. With assistance, position bumper. Engage nylon
end supports to brackets.
12. If necessary, slacken bolts securing end support
brackets. Align bumper to body. Tighten to
29
Nm. (22 lbf.ft)
13. Fit bumper mounting bolts. Tighten to
70 Nm.
(52 lbf.ft)
14. Fit bolt covers.
15. Secure bumper end clips.
16. Connect towing harness multiplugs.
17. Position wheel arch liner extensions. Secure with
screws.
18. Position mud flaps. Secure with screws.
19. Fit road wheels. Tighten to
108 Nm. (80 lbf.ft)
20. Remove safety stands. Lower vehicle.
FASCIA ASSEMBLY
Service repair no - 76.46.23/99
WARNING: The fascia assembly houses
the heater distribution unit, blower
assemblies and air conditioning
evaporator. Assistance is essential during
removal and refit procedures.
CAUTION: When removed from the
vehicle, the fascia should be placed on a
soft covered work surface, supported on
suitable wooden blocks.
Remove
1. Vehicles with SRS only: Remove battery.
See
ELECTRICAL, Repair.
2. Vehicles without SRS: Disconnect battery
negative lead.
3. Drain cooling system.
See COOLING SYSTEM,
Repair.
4. Loosen hose clips, disconnect hoses from
heater pipes.
5. Remove centre console.
See this section.
6. Remove steering column.
See STEERING,
Repair.
7. Remove wiper motor and linkage.
See WIPERS
AND WASHERS, Repair.
8. Disconnect passenger side heated front screen
multiplug. Release multiplug from clip.
76
CHASSIS AND BODY
NEW RANGE ROVER
14
REPAIR
9. Remove 6 bolts, remove remaining scuttle side
panel.
10. Remove heater intake pollen filters.
11. Remove 8 screws securing each pollen filter
housing. Remove both housings.
12. Remove radio.
See ELECTRICAL, Repair.
13. Release door aperture seal adjacent to ’A’ post
lower trim panels.
14. Driver’s side - LHD automatic vehicles only:
Remove 3 bolts securing foot rest through ’A’
post lower trim, remove foot rest.
15. Remove screw securing each ’A’ post lower trim
panel, release from single sprag clip, remove
both trim panels.
CHASSIS AND BODY
15
REPAIR
16. Remove fuse cover from driver’s seat base trim.
17. Remove screw and 2 trim studs, remove seat
base trim.
18. Release 4 sprag clips, remove driver’s side
carpet retainer.
19. Remove 2 scrivet fasteners securing lower
closing panel to passenger side of fascia.
20. Release closing panel, disconnect footwell lamp,
release diagnostic multiplug. Remove closing
panel.
21. Remove 4 bolts, remove fascia centre bracket.
76
CHASSIS AND BODY
NEW RANGE ROVER
16
REPAIR
22. Disconnect 4 multiplugs from Body Electrical
Control Module (BeCM)
23. Remove captive nut, remove earth wires from
stud at base of driver’s side ’A’ post.
24. Disconnect multiplugs at base of each ’A’ post.
25. Release BeCM harness from sill, route into
fascia to prevent fouling as fascia is removed.
26. Disconnect multiplugs and release vacuum hose
from brake and clutch switches.
27. Models with SRS only: Disconnect SRS
multiplug from main harness.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст