Discovery (1995+): Body Repair Manual — part 22
76
CHASSIS AND BODY
26
REPAIR
REAR SEAT SQUAB
Service repair no - 76.70.38
Remove
1. Fold the rear seat down.
2. Remove the two seat squab securing bolts.
3. Withdraw the seat squab from the seat
assembly.
Refit
4. Reverse removal procedure.
REAR SEAT SQUAB COVER
Service repair no - 76.70.79/80
Remove
1. Remove the rear seat squab from the seat
assembly and withdraw it from the vehicle.
See
this section.
2. Remove the rear seat back finisher from the
squab.
3. Remove the squab striker plate.
4. Release the squab cover from the frame.
5. Remove the securing clips and remove the
cover from the squab.
Refit
6. Reverse removal procedure.
CHASSIS AND BODY
27
REPAIR
REAR SEAT CUSHION COVER
Service repair no - 76.70.88/89
Remove
NOTE: The procedure for removing both
left and right hand seat cushions is the
same.
1. Remove the rear seat assembly from the
vehicle.
See this section.
2. Remove the seat squab.
3. Remove the seat cushion.
4. Remove the cushion base cover retaining
screws and withdraw the cover.
5. Release the seat cover securing clips at the
frame and at the seat belt aperture.
6. Remove the cover from the cushion.
Refit
7. Reverse removal procedure.
SPLIT REAR SEAT LOCKING MECHANISM
Service repair no - 76.70.51
Remove
1. Remove the front body side trim casing.
See
this section.
2. Remove the three screws securing the latch to
the tower, noting that access to the single screw
is gained through the hole in the front of the
tower.
3. Retrieve the latch from the opening at the rear of
the tower. If necessary retrieve the single screw.
4. The operating rod can be removed from the latch
by releasing it at the plastic clip.
Refit
5. Reverse removal procedure. Setting the release
button to achieve a gap of 5 - 8 mm (3/16 - 5/16
in).
76
CHASSIS AND BODY
28
REPAIR
REAR FOLD DOWN SEATS
Service repair no - 76.71.23
Seat and squab
Remove
1. Locate the seat in the down position, release the
seat belt strap and buckle from their stowed
positions.
2. Remove 4 Torx screws from the lower brackets.
3. Fold the seat up and remove the 2 Torx screws
from the upper brackets. Collect 4 washers.
4. Remove seat assembly.
Refit
5. Position seat assembly, align upper brackets,
and secure with Torx screws tightened to
13 Nm
(10 lbf ft) .
NOTE: Ensure washers are fitted in their
correct positions.
6. Align lower brackets, fit Torx screws and tighten
to
13 Nm (10 lbf ft) .
7. Secure the seat belt strap and buckle to their
stowed positions.
Seat squab
Remove
8. Remove the seat assembly from the vehicle.
9. Remove the pivot bolts and washers securing
the seat squab to the frame.
NOTE: The pivot bolts, securing the seat
squab and cushion, are fitted with a wavy
washer under the head and a plain washer
between the link or bracket. Ensure that these
washers are fitted in the correct locations when
reassembling the seat.
CHASSIS AND BODY
29
REPAIR
10. Remove the pivot bolts and washers securing
the hinge links to the seat squab.
11. If necessary remove the clips securing the cover
and detach the cover.
Refit
12. Reverse removal procedure.
Seat cushion
Remove
13. Remove the seat from the vehicle.
14. Remove the seat squab.
15. Remove the pivot bolts and washers securing
the hinge bracket and detach the bracket.
16. Invert the seat base and remove the screws and
rivets securing the base cover to the base.
17. Raise the seat base cover, to gain access to the
stay pivot bolts, remove the bolts and washers
and withdraw the stay and seat base cover.
18. If necessary remove the clips and detach the
cushion cover.
Refit
19. Reverse removal procedure.
FRONT SEAT BELTS
Service repair no - 76.73.10
Remove
1. Move the front seat to the fully forward position
or tilt the seat forward (3 door vehicles).
2. Remove cover to gain access to the seat belt
upper mounting bolt.
NOTE: 3 door models have a
non-adjustable, upper mounting.
3. Remove the flanged securing bolt to release the
upper mounting and spacer.
4. Remove the cover and bolt securing the lower
mounting to the floor.
5. Detach the door seals from the ’B’ post
sufficiently to allow removal of the lower trim
panel from the post.
6. Release the seat belt from the split section at the
top of the trim panel and withdraw the panel.
7. Remove the securing bolt and detach the inertia
reel from the bottom of the ’B’ post.
5 door model illustrated
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст