Discovery 2. Manual — part 727
WIPERS AND WASHERS
REPAIRS
84-23
6. Remove nut securing linkage connecting rod to
wiper motor spindle.
7. Release link from motor spindle.
8. Remove 3 bolts securing motor to mounting
plate and remove motor.
Refit
1. Fit new wiper motor to mounting plate and
secure with bolts.
2. Connect link to motor spindle and tighten nut to
7 Nm (5.2 lbf.ft).
3. Fit motor and linkage to body, connect
multiplug. Tighten all fixings to 2.5 Nm (1.8
lbf.ft).
4. Fit plenum air intake.
Switch - wiper and washer - windscreen
$% 84.15.34
WARNING: It is imperative that before any work
is undertaken on the SRS system the appropriate
information is read thoroughly.
Remove
1. Remove rotary coupler.
2. Release passive coil from steering column lock
and lower the coil without disconnecting the
harness.
3. Release front wiper delay multiplug from
column switch mounting bracket and
disconnect from harness.
4. Disconnect harness multiplug from wiper
switch.
5. Remove 2 screws securing switch, carefully
raise edge of switch bracket to clear location
peg and remove switch.
Refit
1. Fit new switch to bracket and secure with
screws.
2. Connect harness multiplug to switch.
WIPERS AND WASHERS
84-24
REPAIRS
3. Connect front wiper delay multiplug and fit
multiplug to switch bracket.
4. Fit passive coil to column lock.
5. Fit rotary coupler.
Jet - washer - headlamp
$% 84.20.08
The procedure to remove the headlamp washer jet
on 03MY vehicles is detailed in the front bumper
finisher job.
EXTERIOR FITTINGS, REPAIRS, Trim
finisher - bumper - front - from 03MY.
Remove
1. Remove retaining screw cover from jet
housing.
2. Remove screw securing jet to bumper.
3. Release jet and withdraw sufficiently to gain
access to washer tube. Disconnect tube from
jet and remove jet.
Refit
1. Connect jet to washer tube, ensuring it is
pushed fully home.
2. Locate jet in bumper, retain with screw and fit
screw cover.
WIPERS AND WASHERS
REPAIRS
84-25
Jet - washer - rear screen
$% 84.30.09
Remove
1. Remove spare wheel.
2. Remove rear screen wiper blade.
3. Release washer jet and washer jet tube from
wiper arm.
4. Release washer jet from washer jet tube and
remove jet.
Refit
1. Fit new washer jet to washer jet tube and fit to
wiper arm.
2. Fit rear screen wiper blade.
3. Fit spare wheel.
Switch - rear wash
$% 84.30.27
Remove
1. Carefully remove switch from instrument cowl.
2. Disconnect multiplug and remove switch.
Refit
1. Position new switch and connect multiplug.
2. Carefully push switch into instrument cowl.
WIPERS AND WASHERS
84-26
REPAIRS
Motor - wiper - rear screen
$% 84.35.12
Remove
1. Remove spare wheel from taildoor.
2. Remove tail door trim casing.
DOORS, REPAIRS, Trim casing - tail
3. Remove tail door water shedder.
4. Disconnect washer tube
5. Raise nut cover, remove nut and release wiper
arm.
6. Remove spindle nut and flat washer and
discard rubber seal.
7. Disconnect taildoor harness multiplug from
wiper motor.
8. Remove 2 bolts securing wiper motor to tail
door.
9. Remove wiper motor.
Refit
1. Position wiper motor to door and secure with
bolts.
2. Connect tail door harness multiplug to wiper
motor.
3. Fit rubber seal, flat washer and spindle nut.
Tighten spindle nut to 3 Nm (2.2 lbf.ft).
4. Position wiper arm to tail door and connect
washer tube.
5. Tighten wiper arm nut to 20 Nm (15 lbf.ft) and
fit nut cover.
6. Fit tail door water shedder.
7. Fit tail door trim casing.
DOORS, REPAIRS, Trim casing - tail
8. Fit spare wheel to tail door.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст