Discovery 2. Manual — part 91
ENGINE MANAGEMENT SYSTEM - V8
REPAIRS 18-2-93
6. Remove 4 bolts securing fuel rail to inlet
manifold.
7. Release injectors from inlet manifold and
remove fuel rail and injectors.
8. Release spring clips securing injectors to fuel
rail and remove fuel injectors.
9. Remove and discard 2 'O' rings from each
injector.
10. Fit protective caps to each end of injectors.
Refit
1. Clean injectors and recesses in fuel rail and
inlet manifold.
2. Lubricate new 'O' rings with silicone grease
and fit to each end of injectors.
3. Fit injectors to fuel rail and secure with spring
clips.
4. Position fuel rail assembly and push-fit each
injector into inlet manifold.
5. Fit bolts securing fuel rail to inlet manifold and
tighten to 9 Nm (7 lbf.ft).
6. Connect fuel feed hose to fuel rail.
7. Connect injector harness multiplugs and
secure to fuel rail.
8. Carefully position ignition coil assembly
between inlet manifold and bulkhead.
9. Fit upper manifold.
SYSTEMS - V8, REPAIRS, Gasket - inlet
manifold - upper - Without Secondary Air
Injection.
ENGINE MANAGEMENT SYSTEM - V8
18-2-94 REPAIRS
Actuator - cruise control
$% 19.75.05
Remove
1. Release clip and disconnect inner cable from
actuator.
2. Release outer cable from actuator mounting
bracket.
3. Release vacuum hose from actuator.
4. Remove nut, and remove actuator from
mounting bracket.
Refit
1. Position actuator and tighten retaining nut.
2. Connect vacuum hose to actuator.
3. Connect outer cable to mounting bracket.
4. Connect inner cable to actuator.
Vacuum control unit - up to 03MY
$% 19.75.06
Remove
1. Disconnect vacuum hose from actuator.
2. Disconnect multiplug from vacuum control unit.
3. Release 3 rubber mountings securing control
unit, and remove from mounting bracket.
4. Remove vacuum hose from control unit.
Refit
1. Position vacuum hose to control unit.
2. Position control unit and secure mountings.
3. Connect multiplug and vacuum hose.
ENGINE MANAGEMENT SYSTEM - V8
REPAIRS 18-2-95
Vacuum control unit - from 03MY
$% 19.75.06
Remove
1. If fitted: Remove 2 nuts securing heat shield
and remove heat shield.
2. Disconnect vacuum hose from actuator.
3. Disconnect multiplug from control unit.
4. Release 3 rubber mounting securing control
unit to mounting bracket and remove control
unit.
Refit
1. Position control unit and secure mountings.
2. Connect multiplug and vacuum hose.
3. If fitted: Fit heat shield, fit nuts and tighten to
10 Nm (7 lbf.ft).
ENGINE MANAGEMENT SYSTEM - V8
18-2-96 REPAIRS
Cable - cruise control
$% 19.75.10
Remove
1. Release clip and disconnect inner cable from
actuator.
2. Release outer cable from actuator mounting
bracket.
3. Loosen cable locknuts, release outer cable
from abutment bracket and retaining clip.
4. Release inner cable from operating lever and
remove cable.
Refit
1. Position cable and connect to operating lever.
2. Position cable to abutment bracket.
3. Position outer cable to actuator mounting
bracket and connect inner cable to actuator.
4. Adjust cruise control cable.
V8, ADJUSTMENTS, Cable - cruise control.
Switch - cruise control (on/off)
$% 19.75.30
Remove
1. Carefully remove switch from instrument cowl.
2. Disconnect multiplug and remove switch.
Refit
1. Position new switch and connect multiplug.
2. Carefully push switch into instrument cowl.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст