Range Rover. Manual — part 102
LAND ROVER V8
9
REPAIR
CRANKSHAFT POSITION (CKP) SENSOR - from
99MY
Service repair no - 18.30.12
Remove
1. Release fixings and remove battery cover.
2. Disconnect battery earth lead.
3. Raise front of vehicle.
WARNING: Support on safety stands.
4. Release CKP sensor multiplug from bracket and
disconnect multiplug from engine harness.
5. Remove 2 bolts securing CKP sensor heat
shield.
6. Remove heat shield.
7. Remove 2 nuts securing CKP sensor, remove 2
spacers, sensor and sensor mounting.
Refit
8. Ensure all components are clean.
9. Fit sensor mounting, CKP sensor, 2 spacers and
tighten sensor retaining nuts to
6 Nm (5 lbf.ft).
10. Fit CKP sensor heat shield and secure with
bolts.
11. Connect sensor multiplug to engine harness and
fit multiplug to bracket.
12. Remove stand(s) and lower vehicle.
13. Connect battery earth lead.
14. Fit and secure battery cover.
19
FUEL SYSTEM
NEW RANGE ROVER
10
REPAIR
FUEL SYSTEM - DEPRESSURISE
WARNING: Fuel pressure of up to 2.5 bar
will be present in the system, even if the
engine has not been run for some time.
Always depressurise the system before
disconnecting any components in the fuel feed
line (between fuel pump and pressure regulator).
The spilling of fuel is unavoidable during this
operation. Ensure that all necessary precautions
are taken to prevent fire and explosion.
NOTE: Fuel pressure can be relieved at
fuel rail feed union or fuel filter unions.
1. Position cloth around relevant union to protect
against fuel spray.
2. Carefully slacken union.
3. Tighten union to correct torque once pressure
has relieved.
ENGINE CONTROL MODULE (ECM) - up to 99MY
Service repair no - 18.30.01
Remove
1. Disconnect battery negative lead.
2. Remove 2 screws securing ECM housing cover.
Remove cover
3. Slacken 2 harness clamp screws.
4. Lift ECM slightly for access. Disconnect 3
multiplugs.
5. Remove ECM from housing.
6. Remove carrier plate from ECM.
Refit
7. Reverse removal procedure.
LAND ROVER V8
11
REPAIR
ENGINE CONTROL MODULE (ECM) - from 99MY
Service repair no - 18.30.01
Remove
1. Release fixings and remove battery cover.
2. Disconnect battery earth lead.
3. Remove 2 screws securing cruise control
assembly to EAS housing cover and position
aside.
4. Release 2 fixings securing ECM housing cover
and release cover.
5. Disconnect ECM cooling fan multiplug.
6. Release ECM from housing cover, disconnect
multiplugs and remove ECM.
Refit
7. Position ECM and connect multiplugs.
8. Fit ECM to housing cover and connect ECM
cooling fan multiplug.
9. Fit ECM housing cover to main housing and
secure with fixings.
10. Position cruise control assembly to EAS housing
cover and secure with screws.
11. Connect battery earth lead.
12. Fit battery cover and secure with fixings.
19
FUEL SYSTEM
NEW RANGE ROVER
12
REPAIR
FAN - ECM COOLING - from 99MY
Service repair no - 18.30.80
Remove
1. Release fixings and remove battery cover.
2. Disconnect battery earth lead.
3. Remove 2 screws securing cruise control
assembly to EAS housing cover and position
aside.
4. Release 2 fixings securing ECM housing cover
and release cover.
5. Disconnect ECM cooling fan multiplug and
position ECM housing cover aside.
6. Release ECM cooling fan multiplug from bracket.
7. Release ECM cooling fan from cooling fan cowl
and remove cooling fan.
8. Remove 2 screws securing cooling fan cowl to
ECM housing and remove cowl.
Refit
9. Remove cooling fan cowl from new cooling fan.
10. Fit cooling fan cowl to ECM housing and secure
with screws.
11. Fit cooling fan to cooling fan cowl and fit
multiplug to bracket.
12. Position ECM housing cover and connect ECM
cooling fan multiplug.
13. Fit ECM housing cover to main housing and
secure with fixings.
14. Position cruise control assembly to EAS housing
cover and secure with screws.
15. Connect battery earth lead.
16. Fit battery cover and secure with fixings.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст