Range Rover. Manual — part 222
SUPPLEMENTARY RESTRAINT SYSTEM
5
REPAIR
20. Remove 2 trim studs securing air cleaner baffle
beneath LH wheel arch. Remove baffle.
21. Disconnect both SRS crash sensor multiplugs.
22. Remove 4 bolts securing battery tray.
75
SUPPLEMENTARY RESTRAINT SYSTEM
NEW RANGE ROVER
6
REPAIR
23. Remove 2 bolts securing air cleaner to valance.
24. Raise air cleaner and battery tray to gain access
to crash sensor harness clips.
25. Release clips securing each crash sensor
harness to valance.
26. Release harness grommets. Feed both
harnesses through valance into wheel arches.
27. Release 3 clips securing each crash sensor
harness to underside of wheel arches.
28. Release harness bulkhead grommets. Feed
harnesses through bulkhead into passenger
compartment.
29. Disconnect SRS multiplug from instrument pack.
SUPPLEMENTARY RESTRAINT SYSTEM
7
REPAIR
30. Disconnect driver’s air bag module connector.
Release connector and harness from clips.
31. Release 13 clips securing SRS harness to fascia
frame.
NOTE: Due to restricted access, two outer
clips ’A’ securing harness above heater
unit may have to be cut. Ensure that
location holes are clear. Collect loose ends of
clips.
32. Release 3 clips securing fascia harness trunking
to passenger side fascia frame.
33. Remove nut securing lower end of each blower
assembly to fascia frame.
34. Route crash sensor ends of harness into
passenger air bag module space.
35. Feed SRS DCU connector into passenger air
bag module space.
36. Remove harness.
Refit
37. Position harness in passenger air bag module
space. Feed SRS DCU connector between
heater and fascia frame.
38. Route harness along transmission tunnel.
Secure harness clips.
39. Connect multiplug to DCU.
40. Fit sound deadener pad to transmission tunnel.
41. Route crash sensor ends of harness correctly
around fascia frame and behind blower
assemblies.
42. Secure harness clips to fascia frame.
43. Position fascia harness trunking. Secure with
clips.
44. Secure blower assemblies to fascia frame with
nuts.
45. Connect drivers air bag module, secure
multiplug and harness to trunking.
46. Connect SRS multiplug to instrument pack.
75
SUPPLEMENTARY RESTRAINT SYSTEM
NEW RANGE ROVER
8
REPAIR
47. Route SRS crash sensor harnesses through
bulkhead into wheel arches, locate harness
grommets.
48. Secure harness clips beneath wheel arches.
49. Route harnesses through valances into engine
bay. Locate harness grommets.
50. Raise battery tray and air cleaner for access.
Route crash sensor harnesses. Secure harness
clips.
51. Connect multiplugs to crash sensors.
52. Secure battery tray and air cleaner with bolts.
53. Connect SRS harness multiplug to main
harness. Secure multiplug to bracket.
54. Fit air cleaner baffle beneath LH wheel arch.
Secure with trim studs.
55. Fit wheel arch liners.
See CHASSIS AND
BODY, Repair.
56. Position driver’s side lower closing panel.
Connect footwell lamp multiplug.
57. Align closing panel. Secure with scrivet
fasteners.
58. Position ’A’ post lower trim panels. Engage
sprag clips. Secure with screws.
59. Re-fit door aperture seals.
60. LHD automatic vehicles only: Position foot
rest. Secure with bolts.
61. Position heater controls. Connect multiplugs.
Secure to fascia with screws.
62. Position fascia switch pack. Connect multiplugs.
Secure to fascia with screws.
63. Fit instrument pack binnacle.
See
INSTRUMENTS, Repair.
64. Fit radio.
See ELECTRICAL, Repair.
65. Fit passenger air bag module.
See this section.
66. Fit centre console.
See CHASSIS AND BODY,
Repair.
67. Fit battery.
See ELECTRICAL, Repair.
68. Remove safety stands. Lower vehicle.
SRS CRASH SENSOR
Service repair no - 76.73.70
Remove
WARNING: Always disconnect negative
lead from battery first. Disconnection of
positive lead with negative lead connected
risks short circuit and severe sparking through
accidental grounding of spanner. Personal injury
could result.
1. Disconnect both battery terminals.
2. Disconnect sensor multiplug.
3. Remove 2 bolts securing sensor to valance.
Remove sensor.
Refit
4. Reverse removal procedure.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст