Range Rover. Manual — part 223
SUPPLEMENTARY RESTRAINT SYSTEM
9
REPAIR
AIRBAG MODULE - DRIVER SIDE
Service repair no - 76.73.71
Remove
1. Disconnect both battery terminals, negative lead
first.
2. Disconnect Supplementary Restraint System
(SRS) ’shorting link’.
3. Unscrew 4 bolts (TX 30 Torx bit) securing
module to steering wheel.
NOTE: Fixings remain captive in steering
wheel.
NOTE: Rotate steering wheel for access to
all fixings.
4. Release module from steering wheel, disconnect
multiplug.
5. Remove module.
CAUTION: Store the airbag module
correctly.
See Description and operation.
Refit
NOTE: If a new airbag module is being
fitted, the serial numbers must be
recorded.
6. Position module and connect multiplug.
7. Tighten bolts to
9 Nm. (7 lbf.ft)
8. Connect SRS ’shorting link’ and secure
connector to location.
9. Connect battery terminals, positive before
negative. Fit and secure battery cover.
10. Check SRS using TestBook .
75
SUPPLEMENTARY RESTRAINT SYSTEM
NEW RANGE ROVER
10
REPAIR
PRE-TENSIONER - SEAT BELT - FRONT - from
99MY
Service repair no - 76.73.75
Remove
WARNING: See SRS safety precautions
before commencement of repair. See
SUPPLEMENTARY RESTRAINT SYSTEM,
Precautions.
1. Remove ’B’ post lower finisher.
See CHASSIS
AND BODY, Repair.
2. Remove bolt securing seat belt to seat and
release belt from seat.
3. Remove cover from upper mounting.
4. Remove nut from upper mounting.
5. Release seat belt guide from ’B’ post.
6. Remove front carpet retainer.
7. Release pre-tensioner multiplug from inner sill
and disconnect multiplug.
SUPPLEMENTARY RESTRAINT SYSTEM
11
REPAIR
8. Remove bolt securing belt reel to ’B’ post.
Remove reel.
WARNING: Store pre-tensioner in
accordance with storage procedures. See
SUPPLEMENTARY RESTRAINT SYSTEM,
Precautions.
Refit
9. Fit reel, fit bolt and tighten to
32 Nm (24 lbf.ft).
10. Connect pre-tensioner multiplug and secure to
inner sill.
11. Fit front carpet retainer.
12. Extend belt and secure belt guide to ’B’ post.
13. Locate belt to upper mounting, fit nut and tighten
to
22 Nm (16 lbf.ft).
14. Fit cover to upper mounting.
15. Position belt to seat mounting, fit bolt and tighten
to
32 Nm (24 lbf.ft).
16. Fit ’B’ post lower finisher
See CHASSIS AND
BODY, Repair.
17. Connect battery, earth lead last.
18. Check SRS using TestBook.
AIRBAG - SIDE IMPACT - from 99MY
Service repair no - 76.74.31 - Driver’s side
Service repair no - 76.74.32 - Passenger’s side
Remove
WARNING: See SRS safety precautions
before commencement of repair. See
SUPPLEMENTARY RESTRAINT SYSTEM,
Precautions.
1. Remove squab cover and squab foam as an
assembly.
See SEATS, Repair.
2. Release airbag harness from clip.
3. Remove 2 nuts securing airbag.
4. Release and remove airbag.
WARNING: Store airbag module in
accordance with storage procedures. See
SUPPLEMENTARY RESTRAINT SYSTEM,
Precautions.
75
SUPPLEMENTARY RESTRAINT SYSTEM
NEW RANGE ROVER
12
REPAIR
Refit
NOTE: If airbag is replaced, bar code of
new airbag must be recorded in vehicle
handbook.
5. Fit airbag and secure with nuts. Tighten to
5.5 Nm (4 lbf.ft).
6. Route harness through slotted hole in seat frame
and secure to clip.
7. Fit squab cover
See SEATS, Repair.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст