Range Rover. Manual — part 227
CHASSIS AND BODY
3
REPAIR
BONNET LOCK - RIGHT HAND
Service repair no - 76.16.25
Remove
1. Release 3 turnbuckles securing battery cover.
Remove cover
2. Remove 2 bolts securing bonnet lock to platform.
3. Manoeuvre lock and disconnect alarm switch
multiplug.
4. Release inner and outer cables from lock.
5. Remove lock.
Refit
6. Reverse removal procedure.
76
CHASSIS AND BODY
NEW RANGE ROVER
4
REPAIR
BONNET SAFETY CATCH
Service repair no - 76.16.34
Remove
1. Remove bolts securing safety catch to bonnet.
2. Remove safety catch.
Refit
3. Position catch to bonnet.
4. Fit bolts, do not tighten.
5. Close and open bonnet to align catch.
6. Secure catch with bolts.
BONNET STRUT
Service repair no - 76.16.14
Remove
1. Support bonnet in open position.
2. Release clip securing strut lower ball joint.
3. Remove screws securing strut bracket to bonnet.
4. Remove strut and bracket.
5. Remove strut from bracket.
Refit
6. Fit strut to bonnet bracket, fit to bonnet.
7. Secure strut to lower ball joint.
8. Fit bracket screws. Remove support, close
bonnet.
CHASSIS AND BODY
5
REPAIR
CENTRE CONSOLE
Service repair no - 76.25.01
Remove
1. Remove electric window switch pack.
See
ELECTRICAL, Repair.
2. Disconnect rear footwell lamp multiplug.
3. Remove base in console bin.
4. Remove nuts securing rear of console to floor
studs.
5. Move both front seats fully rearward.
6. Remove 2 screws securing each side panel to
centre console. Release sprag clips from fascia
switch pack by firmly pulling rearwards. Remove
side panels.
7. Remove screw at rear of gear lever applique.
Raise rear end of applique to disengage 2 spring
clips at forward end.
8. Disconnect cigar lighter multiplug, release cigar
lighter bulb. Remove gear lever applique.
9. Manual gearbox models:
Remove gear knob. Remove 2 bolts securing
front of console to floor.
10. Automatic gearbox models:
Remove 2 screws securing selector lever.
11. Remove selector lever.
76
CHASSIS AND BODY
NEW RANGE ROVER
6
REPAIR
12. Remove 3 screws securing selector graphics
plate.
13. Raise selector graphics plate, disconnect
multiplug.
14. Remove selector graphics plate.
15. All models:
Remove clip securing park brake lever clevis pin,
remove clevis pin. Raise park brake lever to
vertical position.
16. Raise rear of console to disengage rear vent
ducts. Remove centre console.
Refit
17. Fit centre console, ensuring that ducts to rear
fresh air vents are correctly engaged.
18. Fit nuts securing centre console to floor.
19. Automatic - position graphics plate over selector
lever, connect multiplug.
20. Align graphics plate to console, secure with
screws.
21. Fit selector lever, secure with screws.
22. Manual - secure front of centre console to floor
with bolts.
23. Fit gear knob.
24. Lower park brake lever, fit clevis pin and secure
pin with clip.
25. Position gear/selector lever applique, connect
cigar lighter multiplug and insert illumination bulb
in holder.
26. Engage applique clips to console. Secure
applique with screw.
27. Position console side panels. Firmly push
forward to engage sprag clips into fascia switch
pack. Fit and tighten screws.
28. Return front seats to original positions.
29. Fit base to console bin, tighten with screws.
30. Connect rear footwell lamp multiplug.
31. Fit electric window switch pack.
See
ELECTRICAL, Repair.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст