Range Rover. Manual — part 228
CHASSIS AND BODY
7
REPAIR
CHASSIS CROSS MEMBER
Service repair no - 76.10.92
Remove
1. Release fixings and remove battery cover.
2. Disconnect battery earth lead.
3. Raise vehicle on 4 post ramp.
4. Support gearbox on a suitable jack.
5. Remove 4 nuts and 2 bolts securing gearbox
mounting to crossmember and discard nuts.
6. Remove gearbox snubber bar.
7. Remove 3 of 4 nuts and bolts securing each side
of crossmember to chassis.
8. With assistance, remove 2 remaining nuts and
bolts securing crossmember and remove
crossmember.
Refit
9. With assistance, fit crossmember and tighten
nuts and bolts to
45 Nm (33 lbf.ft).
10. Fit gearbox snubber bar and tighten bolts to
45
Nm (33 lbf.ft).
11. Fit new nuts securing gearbox mounting to
crossmember and tighten to
45 Nm (33 lbf.ft).
12. Remove support from gearbox.
13. Lower vehicle.
14. Connect battery earth lead.
15. Fit battery cover and secure with fixings.
76
CHASSIS AND BODY
NEW RANGE ROVER
8
REPAIR
ENGINE ACOUSTIC COVER
Service repair no - 76.11.06
Remove
1. Raise front of vehicle.
WARNING: Support on safety stands.
2. Release 4 threaded fasteners securing engine
acoustic cover to chassis brackets.
3. Release acoustic cover from brackets and
manoeuvre past steering gear.
Refit
4. Fit acoustic cover to brackets and secure with
threaded fasteners.
GEARBOX LOWER ACOUSTIC COVER
Service repair no - 76.11.13
Remove
1. Raise front of vehicle.
WARNING: Support on safety stands.
2. Release 6 threaded fasteners securing lower
acoustic cover to side acoustic covers.
3. Remove lower acoustic cover.
Refit
4. Fit acoustic cover to side acoustic covers.
5. Tighten threaded fasteners securing lower cover
to side covers.
6. Remove stand(s) and lower vehicle.
CHASSIS AND BODY
9
REPAIR
GEARBOX ACOUSTIC COVER - RH
Service repair no - 76.11.14
Remove
1. Raise front of vehicle.
WARNING: Support on safety stands.
2. Remove gearbox lower acoustic cover.
See this
section.
3. Remove bolt securing RH acoustic cover to
crossmember.
4. Remove bolt securing RH acoustic cover to
chassis member.
5. Remove gearbox RH acoustic cover.
Refit
6. Fit acoustic cover to chassis and secure with
bolts.
7. Fit gearbox lower acoustic cover.
See this
section.
GEARBOX ACOUSTIC COVER - LH
Service repair no - 76.11.15
Remove
1. Raise front of vehicle.
WARNING: Support on safety stands.
2. Remove gearbox lower acoustic cover.
See this
section.
3. Remove bolt securing LH acoustic cover to
crossmember.
4. Remove bolt securing LH acoustic cover to
chassis member.
5. Remove gearbox LH acoustic cover.
Refit
6. Fit acoustic cover to chassis and secure with
bolts.
7. Fit gearbox lower acoustic cover.
See this
section.
76
CHASSIS AND BODY
NEW RANGE ROVER
10
REPAIR
FRONT BUMPER VALANCE
Service repair no - 76.22.72
Remove
1. Raise the vehicle.
WARNING: Support on safety stands.
2. Remove battery cover for access to RH fog
lamp.
3. Disconnect fog lamp multiplugs and breather
hoses.
4. Release 2 clips securing bumper ends to
mounting brackets.
CAUTION: Loosen bolts securing bumper
end mounting brackets to chassis frame to
avoid damage to sealing rubber during
bumper remove and refit.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст