Range Rover. Manual — part 46
LAND ROVER V8
3
REPAIR
7. Lubricate outer face of seal and fit seal to front
cover using LRT-12-089
8. Fit crankshaft pulley and tighten bolt to
270 Nm
(200 lbf.ft.).
9. Remove LRT-12-080 from crankshaft pulley.
10. Fit auxiliary drive belt.
See ELECTRICAL,
Repair.
CRANKSHAFT REAR OIL SEAL
Service repair no - 12.21.20
Remove
1. Manual Vehicles: Remove flywheel.
See this
section.
2. Automatic Vehicles: Remove drive plate.
See
this section.
3. Remove oil seal from location.
CAUTION: Do not damage seal location or
running surface on crankshaft.
Refit
4. Ensure both seal location and running surface
on crankshaft are clean.
5. Ensure mating faces of flywheel and crankshaft
are clean.
6. Lubricate seal guide LRT-12-095 with clean
engine oil. Position over crankshaft boss.
12
ENGINE
NEW RANGE ROVER
4
REPAIR
7. Lubricate oil seal lip.
8. Position seal squarely. Remove guide.
9. Drift seal into location using LRT-12-091.
10. Manual Vehicles: Fit flywheel.
See this
section.
11. Automatic Vehicles: Fit drive plate.
See this
section.
DRIVE PLATE - AUTOMATIC - up to 99MY
Service repair no - 12.53.13
Remove
1. Remove automatic gearbox and torque
converter.
See AUTOMATIC GEARBOX,
Repair.
2. Remove 4 clamp ring bolts. Collect clamp ring.
3. Remove flexible drive plate/starter ring gear
assembly from hub aligner.
4. Remove 6 screws from hub aligner. Remove hub
aligner from crankshaft. Collect spacer.
5. Check drive plate for distortion or cracks. Check
starter ring gear for chipped or broken teeth. If
either component shows signs of damage, fit a
new assembly.
LAND ROVER V8
5
REPAIR
Refit
6. Ensure all mating surfaces are clean.
7. Fit spacer and hub aligner to crankshaft.
8. Fit hub aligner screws. Tighten to
85 Nm (63
lbf.ft)
9. Fit drive plate and clamp ring.
10. Fit clamp ring bolts. Tighten to
45 Nm (33 lbf.ft)
11. Fit automatic gearbox and converter assembly.
See AUTOMATIC GEARBOX, Repair.
DRIVE PLATE - AUTOMATIC - from 99MY
Service repair no - 12.53.13
Remove
1. Remove gearbox.
See AUTOMATIC
GEARBOX, Repair.
2. Remove CKP sensor.
See FUEL SYSTEM,
Repair.
3. Remove Lucar from starter solenoid.
4. Remove nut securing battery lead to starter
solenoid and disconnect lead.
5. Remove 2 Allen screws securing starter motor
and remove starter motor.
6. Remove 4 bolts securing drive plate clamp ring
and remove ring.
7. Remove drive plate from hub.
8. Remove spacer.
9. Remove starter ring gear.
12
ENGINE
NEW RANGE ROVER
6
REPAIR
Refit
10. Clean starter ring gear and hub, clean dowel and
dowel hole.
11. Fit starter ring gear to hub.
12. Clean spacer, clamp ring and mating face on
hub.
13. Clean drive plate and check for cracks and
distortion.
14. Fit spacer to hub, fit drive plate and clamp ring.
Tighten bolts to
45 Nm (33 lbf.ft).
15. Clean starter motor and mating face.
16. Fit starter motor and tighten Allen screws to
45
Nm (33 lbf.ft).
17. Connect battery lead to starter solenoid and
secure with nut.
18. Connect lucar to starter solenoid.
19. Fit CKP sensor.
See FUEL SYSTEM, Repair.
20. Fit gearbox.
See AUTOMATIC GEARBOX,
Repair.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст