Range Rover. Manual — part 178
STEERING
7
REPAIR
Refit
11. Position feed hose to vehicle.
12. Remove plugs from hose and PAS pump.
13. Clean hose and PAS pump union.
14. V8 up to 99MY: Connect feed hose union to
PAS pump and tighten to
16 Nm (12 lbf.ft).
V8 from 99MY and diesel: Connect feed hose
to pump using new sealing washers. Tighten
banjo bolt to
25 Nm (18 lbf.ft) (V8 models) or 30
Nm (22 lbf.ft) (diesel models).
15. Remove plugs from hose and steering box.
16. Clean hose and steering box union.
17. Position PAS hose brackets to steering box and
secure with nut.
18. Fit banjo bolt and new washers to feed hose and
fit to steering box. Tighten banjo bolt to
30 Nm
(22 lbf.ft)
19. Position feed hose and secure to radiator lower
bracket clips.
20. Bleed steering system.
See this section.
21. Remove stand(s) and lower vehicle.
STEERING BOX RETURN HOSE
Service repair no - 57.15.22
Remove
1. Disconnect battery earth lead.
2. Raise front of vehicle.
WARNING: Support on safety stands.
3. Position container to catch spillage.
4. Remove 2 bolts securing PAS fluid reservoir to
radiator bracket.
5. Remove clip securing return hose to PAS fluid
reservoir and disconnect return hose.
CAUTION: Plug the connections.
6. Position cloth to catch spillage.
57
STEERING
NEW RANGE ROVER
8
REPAIR
7. Remove banjo bolt securing pump return hose to
steering box and discard 2 washers.
CAUTION: Plug the connections.
8. Remove nut securing PAS hose brackets to
steering box.
9. Release PAS hose brackets from stud.
10. Release PAS pipe from 2 radiator lower bracket
clips.
11. Remove pump return hose.
Refit
12. Position return hose to vehicle.
13. Remove plugs from hose and PAS fluid
reservoir.
14. Clean hose and PAS pump union.
15. Connect return hose union to PAS fluid reservoir
and secure with clip.
16. Remove plugs from hose and steering box.
17. Clean hose and steering box union.
18. Position PAS hose brackets to steering box and
secure with nut.
19. Fit banjo bolt and NEW washers to return hose
and fit to steering box. Tighten banjo bolt to
50
Nm (37 lbf.ft)
20. Position return hose and secure to radiator lower
bracket clips.
21. Bleed steering system.
See this section.
22. Remove stand(s) and lower vehicle.
STEERING
9
REPAIR
COLUMN NACELLE
Service repair no - 57.40.29
Remove
1. Remove ignition key.
2. Remove instrument binnacle.
See
INSTRUMENTS, Repair.
3. Release steering column tilt lever, fully extend
and tilt column down.
4. Remove 2 screws securing upper column
nacelle.
5. Release upper column nacelle from side fillet
clips and remove upper nacelle.
6. Remove 4 screws securing lower nacelle,
disengage from side fillet clips and remove
nacelle.
7. Collect side fillets.
Refit
8. Position upper and lower nacelles, loosely fit
screws.
9. Position side fillets, engage clips.
10. Tighten nacelle screws.
11. Fit instrument binnacle.
See INSTRUMENTS,
Repair.
12. Return steering column to original position.
13. Fit ignition key.
OIL RESERVOIR
Service repair no - 57.15.08.
Remove
1. Place tray to catch fluid.
CAUTION: Power steering fluid damages
paintwork. Any spillage must be cleaned
immediately.
2. Disconnect battery negative lead.
3. Remove clips securing hoses to reservoir.
Release hoses.
4. Slacken clamp screw securing reservoir.
Remove reservoir.
Refit
5. Position reservoir. Tighten clamp screw.
6. Connect hoses to reservoir. Secure with new
clips.
7. Fill reservoir.
See LUBRICANTS, FLUIDS AND
CAPACITIES, Information.
8. Reconnect battery negative lead.
9. Bleed power steering.
See this section.
57
STEERING
NEW RANGE ROVER
10
REPAIR
POWER STEERING SYSTEM - BLEED
Service repair no - 57.15.02
1. Fill reservoir to upper mark on dipstick.
See
LUBRICANTS, FLUIDS AND CAPACITIES,
Information.
2. Turn steering wheel 45
°
in both directions to
open valves inside steering box.
3. Top up steering reservoir fluid level.
CAUTION: Do not run engine with less
than minimum fluid level in reservoir. Top
up as necessary during bleed procedure.
4. Start engine. Allow to idle.
5. Turn steering wheel back and forth to open
valves inside steering box.
WARNING: Fluid is under high pressure,
open bleed screw with caution.
6. With engine running, carefully open bleed screw
until fluid starts to flow. Tighten bleed screw to
4 Nm (3 lbf.ft)
7. Switch off engine. Top up reservoir.
STEERING BOX
Service repair no - 57.30.01
Remove
1. Disconnect battery negative lead.
2. Raise the vehicle.
WARNING: Support on safety stands.
3. Remove washer reservoir RHD only.
See
WIPERS AND WASHERS, Repair.
4. Remove nut connecting drag link to drop arm.
Separate drag link from drop arm with
LRT-57-018.
CAUTION: To prevent damage to rotary
coupler, remove key from ignition switch.
Engage steering lock.
5. Remove bolts securing steering column lower
universal joint to steering box.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст