Frelander 2. Manual — part 14
DTC
Description
Possible Cause
Action
Removal and Installation).
C0036-07 Left Rear Tone Wheel -
Mechanical Failure
Bearing encoder
damaged
Install a new left rear wheel bearing.
For additional information, refer to:
Rear W heel
Bearing
(204-02 Rear Suspension, Removal and
Installation).
C0037-01 Left Rear Wheel Speed
Sensor - General electrical
failure
Wheel speed sensor
circuit - short to
ground, short to
power, open circuit
Wheel speed sensor
failure
Carry out pinpoint tests associated with this
DTC using the manufacturer approved diagnostic
system. Clear DTC and retest if DTC returns.
Install a new wheel speed sensor as required.
For additional information, refer to:
Rear W heel
Speed Sensor
(206-09A Anti-Lock Control,
Removal and Installation).
C0037-07 Left Rear Wheel Speed
Sensor - Mechanical Failure
Wheel speed sensor
faulty/incorrectly
installed
Carry out pinpoint tests associated with this
DTC using the manufacturer approved diagnostic
system. Clear DTC and retest if DTC returns.
Check sensor for correct installation. Install a
new wheel speed sensor as required.
For additional information, refer to:
Rear W heel
Speed Sensor
(206-09A Anti-Lock Control,
Removal and Installation).
C003907 Right Rear Tone W heel -
Mechanical Failure
Bearing encoder
damaged
Install a new right rear wheel bearing.
For additional information, refer to:
Rear W heel
Bearing
(204-02 Rear Suspension, Removal and
Installation).
C003A-01 Left Rear Wheel Speed
Sensor - General electrical
failure
Wheel speed sensor
circuit - short to
ground, short to
power, open circuit
Wheel speed sensor
failure
Carry out pinpoint tests associated with this
DTC using the manufacturer approved diagnostic
system. Clear DTC and retest if DTC returns.
Install a new wheel speed sensor as required.
For additional information, refer to:
Rear W heel
Speed Sensor
(206-09A Anti-Lock Control,
Removal and Installation).
C003A-07 Right Rear Wheel Speed
Sensor - Mechanical Failure
Wheel speed sensor
faulty/incorrectly
installed
Carry out pinpoint tests associated with this
DTC using the manufacturer approved diagnostic
system. Check sensor for correct installation.
Clear DTC and retest if DTC returns. Install a
new wheel speed sensor as required.
For additional information, refer to:
Rear W heel
Speed Sensor
(206-09A Anti-Lock Control,
Removal and Installation).
C0040-64 Brake Pedal Switch “A” -
Signal plausibility failure
Brake pedal switch
circuit - short to
ground, short to
power, open circuit
Brake pedal switch
failure
Carry out pinpoint tests associated with this
DTC using the manufacturer approved diagnostic
system. Clear DTC and retest if DTC returns.
Install a new brake switch as required.
For additional information, refer to:
Speed
Control Deactivator Switch
(310-03A Speed
Control - I6 3.2L Petrol, Removal and
Installation).
C0044-01 TMC Pressure Sensor -
General electrical failure
• NOTE: The sensor is
internal to the control
module
Sensor failure
Clear DTC and retest if DTC returns. Install a
new ABS module, refer to the new
module/component installation note at the top
of the DTC Index
C0044-28 TMC Pressure Sensor -
Signal Offset
• NOTE: The sensor is
internal to the control
module
Sensor failure
Clear DTC and retest if DTC returns. Install a
new ABS module, refer to the new
module/component installation note at the top
of the DTC Index
C0044-64 TMC Pressure Sensor -
Signal plausibility
• NOTE: The sensor is
internal to the control
module
Sensor failure
Clear DTC and retest if DTC returns. Install a
new ABS module, refer to the new
module/component installation note at the top
of the DTC Index
C0051-28 Steering wheel rotation
sensor - Off-set monitoring
Sensor
loose/incorrectly
installed
Vehicle track
incorrectly adjusted
Check the sensor and encoder wheel for correct
installation/alignment. Check the steering and
suspension for damage/wear which could affect
the track, rectify as necessary
C0061-01 Lateral Acceleration Sensor
- General Electrical Failure
Sensor circuit - short
to ground, short to
power, open circuit
Internal sensor
failure
Carry out pinpoint tests associated with this
DTC using the manufacturer approved diagnostic
system. Clear DTC and retest if DTC returns.
Install a new sensor
Using the manufacturer approved diagnostic
DTC
Description
Possible Cause
Action
system, carry out the lateral accelerometer
calibration routine
For additional information, refer to:
Accelerometer
(206-09C Anti-Lock Control -
Stability Assist, Removal and Installation).
C0061-28 Lateral Acceleration Sensor
- Signal bias level out of
range/zero adjustment
failure
Sensor incorrectly
calibrated
Clear DTC and retest if DTC returns
Using the manufacturer approved diagnostic
system, carry out the lateral accelerometer
calibration routine
For additional information, refer to:
Accelerometer
(206-09C Anti-Lock Control -
Stability Assist, Removal and Installation).
C0061-64 Lateral Acceleration Sensor
- Signal plausibility failure
Lateral acceleration
sensor internal
failure
Carry out pinpoint tests associated with this
DTC using the manufacturer approved diagnostic
system. Clear DTC and retest if DTC returns.
Install a new sensor
Using the manufacturer approved diagnostic
system, carry out the lateral accelerometer
calibration routine
For additional information, refer to:
Accelerometer
(206-09C Anti-Lock Control -
Stability Assist, Removal and Installation).
C0062-01 Longitudinal Acceleration
Sensor - General electrical
failure
Sensor circuit - short
to ground, short to
power, open circuit
Internal sensor
failure
Carry out pinpoint tests associated with this
DTC using the manufacturer approved diagnostic
system. Clear DTC and retest if DTC returns.
Install a new sensor
Using the manufacturer approved diagnostic
system, carry out the longitudinal accelerometer
calibration routine
For additional information, refer to:
Accelerometer
(206-09C Anti-Lock Control -
Stability Assist, Removal and Installation).
C0062-28 Longitudinal Acceleration
Sensor - Signal bias level
out of range/zero
adjustment failure
Sensor incorrectly
calibrated
Clear DTC and retest if DTC returns
Using the manufacturer approved diagnostic
system, carry out the longitudinal accelerometer
calibration routine
For additional information, refer to:
Accelerometer
(206-09C Anti-Lock Control -
Stability Assist, Removal and Installation).
C0062-64 Longitudinal Acceleration
Sensor - Signal plausibility
failure
Longitudinal
Acceleration sensor
internal failure
Carry out pinpoint tests associated with this
DTC using the manufacturer approved diagnostic
system. Clear DTC and retest if DTC returns.
Install a new sensor
Using the manufacturer approved diagnostic
system, carry out the longitudinal accelerometer
calibration routine
For additional information, refer to:
Accelerometer
(206-09C Anti-Lock Control -
Stability Assist, Removal and Installation).
C0063-01 Yaw Rate Sensor - General
electrical failure
Yaw rate sensor
circuit - short to
ground, power, open
circuit
Yaw rate sensor
internal failure
Refer to electrical circuit diagrams and check
Yaw rate sensor circuit for short to ground,
power, open circuit. Clear DTC and retest if DTC
returns. Install a new sensor
Using the manufacturer approved diagnostic
system, carry out the yaw rate sensor
calibration routine
For additional information, refer to:
Accelerometer
(206-09C Anti-Lock Control -
Stability Assist, Removal and Installation).
C0063-28 Yaw Rate Sensor - Signal
bias level out of range/zero
adjustment failure
Sensor incorrectly
calibrated
Clear DTC and retest if DTC returns.
Using the manufacturer approved diagnostic
system, carry out the yaw rate sensor
calibration routine
For additional information, refer to:
Accelerometer
(206-09C Anti-Lock Control -
Stability Assist, Removal and Installation).
C0063-64 Yaw Rate Sensor - Signal
plausibility failure
Yaw rate sensor
internal failure
Carry out pinpoint tests associated with this
DTC using the manufacturer approved diagnostic
system. Clear DTC and retest if DTC returns.
Install a new sensor
Using the manufacturer approved diagnostic
system, carry out the yaw rate sensor
calibration routine
For additional information, refer to:
Accelerometer
(206-09C Anti-Lock Control -
Stability Assist, Removal and Installation).
General Information - Diagnostic Trouble Code (DTC) IndexDTC: Audio
Front Control Module (ACM)
Description and Operation
• NOTE: If a control module or component is suspect and the vehicle remains under manufacturer warranty, refer to the
Warranty Policy and Procedures manual (section B1.2), or determine if any prior approval program is in operation, before
the replacement of a component.
• NOTE: Generic scan tools may not read the codes listed, or may read only 5-digit codes. Match the 5 digits from the scan
tool to the first 5 digits of the 7-digit code listed to identify the fault (the last 2 digits give extra information read by the
manufacturer-approved diagnostic system).
• NOTE: When performing voltage or resistance tests, always use a digital multimeter (DMM) accurate to three decimal
places, and with an up-to-date calibration certificate. W hen testing resistance always take the resistance of the DMM
leads into account.
• NOTE: Check and rectify basic faults before beginning diagnostic routines involving pinpoint tests.
• NOTE: Inspect connectors for signs of water ingress, and pins for damage and/or corrosion.
• NOTE: If DTCs are recorded and, after performing the pinpoint tests, a fault is not present, an intermittent concern may
be the cause. Always check for loose connections and corroded terminals.
Description And Operation
For a detailed description of the audio front control system, refer to the relevant Description and Operation section in the
workshop manual.
For additional information, refer to:
Audio System
(415-01 Information and Entertainment System, Description and
Operation).
Audio Front Control Module (ACM)
DTC
Description
Possible Cause
Action
B1134-11 Phone input
Phone input circuit - short
to ground
Refer to electrical circuit diagrams and check phone input
circuit for short to ground
B1134-12 Phone input
Phone input circuit - short
to power
Refer to electrical circuit diagrams and check phone input
circuit for short to power
B1134-13 Phone input
Phone input circuit - open
circuit
Refer to electrical circuit diagrams and check phone input
circuit for open circuit
B1A01-11 Speaker #1
Left front speaker circuit -
short to ground
Refer to electrical circuit diagrams and check left front
speaker circuit for short to ground
B1A01-12 Speaker #1
Left front speaker circuit -
short to power
Refer to electrical circuit diagrams and check left front
speaker circuit for short to power
B1A01-1A Speaker #1
Left front speaker circuit -
resistance below threshold
Carry out pinpoint tests associated with this DTC using the
manufacturer approved diagnostic system
B1A01-1B Speaker #1
Left front speaker circuit -
resistance above threshold
Carry out pinpoint tests associated with this DTC using the
manufacturer approved diagnostic system
B1A01-1C Speaker #1
Left front speaker circuit -
voltage out of range
Carry out pinpoint tests associated with this DTC using the
manufacturer approved diagnostic system
B1A02-11 Speaker #2
Right front speaker circuit -
short to ground
Refer to electrical circuit diagrams and check right front
speaker circuit for short to ground
B1A02-12 Speaker #2
Right front speaker circuit -
short to power
Refer to electrical circuit diagrams and check right front
speaker circuit for short to power
B1A02-1A Speaker #2
Right front speaker circuit -
resistance below threshold
Carry out pinpoint tests associated with this DTC using the
manufacturer approved diagnostic system
B1A02-1B Speaker #2
Right front speaker circuit -
resistance above threshold
Carry out pinpoint tests associated with this DTC using the
manufacturer approved diagnostic system
B1A02-1C Speaker #2
Right front speaker circuit -
voltage out of range
Carry out pinpoint tests associated with this DTC using the
manufacturer approved diagnostic system
B1A03-11 Speaker #3
Left rear speaker circuit -
short to ground
Refer to electrical circuit diagrams and check left rear
speaker circuit for short to ground
B1A03-12 Speaker #3
Left rear speaker circuit -
short to power
Refer to electrical circuit diagrams and check left rear
speaker circuit for short to power
B1A03-1A Speaker #3
Left rear speaker circuit -
resistance below threshold
Carry out pinpoint tests associated with this DTC using the
manufacturer approved diagnostic system
B1A03-1B Speaker #3
Left rear speaker circuit -
resistance above threshold
Carry out pinpoint tests associated with this DTC using the
manufacturer approved diagnostic system
DTC
Description
Possible Cause
Action
B1A03-1C Speaker #3
Left rear speaker circuit -
voltage out of range
Carry out pinpoint tests associated with this DTC using the
manufacturer approved diagnostic system
B1A04-11 Speaker #4
Right rear speaker circuit -
short to ground
Refer to electrical circuit diagrams and check right rear
speaker circuit for short to ground
B1A04-12 Speaker #4
Right rear speaker circuit -
short to power
Refer to electrical circuit diagrams and check right rear
speaker circuit for short to power
B1A04-1A Speaker #4
Right rear speaker circuit -
resistance below threshold
Carry out pinpoint tests associated with this DTC using the
manufacturer approved diagnostic system
B1A04-1B Speaker #4
Right rear speaker circuit -
resistance above threshold
Carry out pinpoint tests associated with this DTC using the
manufacturer approved diagnostic system
B1A04-1C Speaker #4
Right front speaker circuit -
voltage out of range
Carry out pinpoint tests associated with this DTC using the
manufacturer approved diagnostic system
B1A56-13 Antenna
Antenna circuit - open
circuit
Refer to electrical circuit diagrams and check antenna circuit
for open circuit
B1B69-11 Antenna 12
volt supply
circuit
Antenna 12 volt supply
circuit - short to ground
Refer to electrical circuit diagrams and check antenna 12 volt
supply circuit for short to ground
B1B69-15 Antenna 12
volt supply
circuit
Antenna 12 volt supply
circuit - short to power,
open circuit
Refer to electrical circuit diagrams and check antenna 12 volt
supply circuit for short to power, open circuit
B1D19-16 Compact disc
unit
Circuit voltage below
threshold
Install a new integrated audio module, refer to the new
module/component installation note at the top of the DTC
Index.
For additional information, refer to:
Audio Unit
(415-01
Information and Entertainment System, Removal and
Installation).
B1D19-77 Compact disc
unit
Commanded position not
reachable
Install a new integrated audio module, refer to the new
module/component installation note at the top of the DTC
Index.
For additional information, refer to:
Audio Unit
(415-01
Information and Entertainment System, Removal and
Installation).
B1D19-93 Compact disc
unit
No operation
Install a new integrated audio module, refer to the new
module/component installation note at the top of the DTC
Index.
For additional information, refer to:
Audio Unit
(415-01
Information and Entertainment System, Removal and
Installation).
B1D78-11 Auxiliary input
Auxiliary input circuit - short
to ground
Refer to electrical circuit diagrams and check auxiliary input
circuit for short to ground
B1D78-12 Auxiliary input
Auxiliary input circuit - short
to power
Refer to electrical circuit diagrams and check auxiliary input
circuit for short to power
B1D78-13 Auxiliary input
Auxiliary input circuit - open
circuit
Refer to electrical circuit diagrams and check auxiliary input
circuit for open circuit
B1D79-11 Microphone
input
Microphone input circuit -
short to ground
Refer to electrical circuit diagrams and check microphone
input circuit for short to ground
B1D79-12 Microphone
input
Microphone input circuit -
short to power
Refer to electrical circuit diagrams and check microphone
input circuit for short to power
B1D79-13 Microphone
input
Microphone input circuit -
open circuit
Refer to electrical circuit diagrams and check microphone
input circuit for open circuit
U3000-49 Control module
Internal electronic failure
Install a new control module, refer to the new
module/component installation note at the top of the DTC
Index.
For additional information, refer to:
Audio Unit
(415-01
Information and Entertainment System, Removal and
Installation).
U3000-55 Control module
Incorrect car configuration
data received
Check/up-date Car Configuration File using manufacturer
approved diagnostic system
U3000-87 Control module
Missing message
Check CJB for DTCs and refer to DTC Index.
For additional information, refer to:
Communications Network
(418-00 Module Communications Network, Diagnosis and
Testing).
Check information and entertainment module for Car
Configuration File and MOST network DTCs and refer to
relevant DTC Index. Carry out MOST/CAN network tests using
the manufacturer approved diagnostic system
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст