Frelander 2. Manual — part 13
DTC
Description
Possible Cause
Action
B1A07-49 Speaker #7
Internal electronic
failure
Install a new module, refer to the new module/component
installation note at the top of the DTC Index
B1A08-11 Speaker #8
Rear Right Surround
Speaker circuit - short
to ground
Refer to electrical circuit diagrams and check Rear Right
Surround Speaker circuit for short to ground
B1A08-12 Speaker #8
Rear Right Surround
Speaker circuit - short
to power
Refer to electrical circuit diagrams and check Rear Right
Surround Speaker circuit for short to power
B1A08-13 Speaker #8
Rear Right Surround
Speaker circuit - open
circuit
Refer to electrical circuit diagrams and check Rear Right
Surround Speaker circuit for open circuit
B1A08-1A Speaker #8
Rear Right Surround
Speaker circuit -
resistance below
threshold
Refer to electrical circuit diagrams and check Rear right
surround speaker connection for crossload
B1A08-49 Speaker #8
Internal electronic
failure
Install a new module, refer to the new module/component
installation note at the top of the DTC Index
B1A09-11 Speaker #9
Center Speaker circuit -
short to ground
Refer to electrical circuit diagrams and check Center Speaker
circuit for short to ground
B1A09-12 Speaker #9
Center Speaker circuit -
short to power
Refer to electrical circuit diagrams and check Center Speaker
circuit for short to power
B1A09-13 Speaker #9
Center Speaker circuit -
open circuit
Refer to electrical circuit diagrams and check Center Speaker
circuit for open circuit
B1A09-1A Speaker #9
Center Speaker circuit -
resistance below
threshold
Refer to electrical circuit diagrams and check Center speaker
connection for crossload
B1A09-49 Speaker #9
Internal electronic
failure
Install a new module, refer to the new module/component
installation note at the top of the DTC Index
B1A10-11 Speaker #10
Left Subwoofer Speaker
circuit - short to
ground
Refer to electrical circuit diagrams and check Left Subwoofer
Speaker circuit for short to ground
B1A10-12 Speaker #10
Left Subwoofer Speaker
circuit - short to power
Refer to electrical circuit diagrams and check Left Subwoofer
Speaker circuit for short to power
B1A10-13 Speaker #10
Left Subwoofer Speaker
circuit - open circuit
Refer to electrical circuit diagrams and check Left Subwoofer
Speaker circuit for open circuit
B1A10-1A Speaker #10
Left Subwoofer Speaker
circuit - resistance
below threshold
Refer to electrical circuit diagrams and check Left subwoofer
speaker connection for crossload
B1A10-49 Speaker #10
Internal electronic
failure
Install a new module, refer to the new module/component
installation note at the top of the DTC Index
B1A11-11 Speaker #11
Right Subwoofer
Speaker circuit - short
to ground
Refer to electrical circuit diagrams and check Right Subwoofer
Speaker circuit for short to ground
B1A11-12 Speaker #11
Right Subwoofer
Speaker circuit - short
to power
Refer to electrical circuit diagrams and check Right Subwoofer
Speaker circuit for short to power
B1A11-13 Speaker #11
Right Subwoofer
Speaker circuit - open
circuit
Refer to electrical circuit diagrams and check Right Subwoofer
Speaker circuit for open circuit
B1A11-1A Speaker #11
Right Subwoofer
Speaker circuit -
resistance below
threshold
Refer to electrical circuit diagrams and check Right subwoofer
speaker connection for crossload
B1A11-49 Speaker #11
Internal electronic
failure
Install a new module, refer to the new module/component
installation note at the top of the DTC Index
B1D84-11 Headphone panel
1
Headphone panel 1 left
or right signal circuit -
short to ground
Refer to electrical circuit diagrams and check headphone panel
1 left or right signal circuit for short to ground
B1D84-13 Headphone panel
1
Headphone panel 1 left
or right signal circuit -
open circuit
Refer to electrical circuit diagrams and check headphone panel
1 left or right signal circuit for open circuit
DTC
Description
Possible Cause
Action
B1D84-23 Headphone panel
1
Headphone panel 1
control line circuit -
signal stuck low
Refer to electrical circuit diagrams and check headphone panel
1 control line for short to ground. Check for stuck switch/button
B1D85-11 Headphone panel
2
Headphone panel 2 left
or right signal circuit -
short to ground
Refer to electrical circuit diagrams and check headphone panel
2 left or right signal circuit for short to ground
B1D85-13 Headphone panel
2
Headphone panel 2 left
or right signal circuit -
open circuit
Refer to electrical circuit diagrams and check headphone panel
2 left or right signal circuit for open circuit
B1D85-23 Headphone panel
2
Headphone panel 2
control line circuit -
signal stuck low
Refer to electrical circuit diagrams and check headphone panel
2 control line for short to ground. Check for stuck switch/button
B1D86-11 Headphone panel
3
Headphone panel 3 left
or right signal circuit -
short to ground
Only 2 headphone panels available on this vehicle. If this DTC
is logged, check/amend Car Configuration File to reflect 2
panels only using the manufacturer approved diagnostic system
B1D86-13 Headphone panel
3
Headphone panel 3 left
or right signal circuit -
open circuit
Only 2 headphone panels available on this vehicle. If this DTC
is logged, check/amend Car Configuration File to reflect 2
panels only using the manufacturer approved diagnostic system
B1D86-23 Headphone panel
3
Headphone panel 3
control line circuit -
signal stuck low
Only 2 headphone panels available on this vehicle. If this DTC
is logged, check/amend Car Configuration File to reflect 2
panels only using the manufacturer approved diagnostic system
B1D87-11 Headphone panel
4
Headphone panel 4 left
or right signal circuit -
short to ground
Only 2 headphone panels available on this vehicle. If this DTC
is logged, check/amend Car Configuration File to reflect 2
panels only using the manufacturer approved diagnostic system
B1D87-13 Headphone panel
4
Headphone panel 4 left
or right signal circuit -
open circuit
Only 2 headphone panels available on this vehicle. If this DTC
is logged, check/amend Car Configuration File to reflect 2
panels only using the manufacturer approved diagnostic system
B1D87-23 Headphone panel
4
Headphone panel 4
control line circuit -
signal stuck low
Only 2 headphone panels available on this vehicle. If this DTC
is logged, check/amend Car Configuration File to reflect 2
panels only using the manufacturer approved diagnostic system
U3000-05 Control module -
system
programming
failures
Software
incompatibility
The version of the
Local Configuration file
does not match that
expected
Re-configure the audio amplifier as an existing control module,
using the manufacturer approved diagnostic system
U3000-42 Control module -
general memory
failure
General memory failure Re-configure the audio amplifier as an existing control module,
using the manufacturer approved diagnostic system. Clear DTC,
cycle ignition and read DTCs. If DTC returns, suspect audio
amplifier module and install a new module. Refer to the new
module/component installation note at the top of the DTC
Index
U3000-44 Control module -
data memory
failure
Data memory failure
Re-configure the audio amplifier as an existing control module,
using the manufacturer approved diagnostic system. Clear DTC,
cycle ignition and read DTCs. If DTC returns, suspect audio
amplifier module and install a new module. Refer to the new
module/component installation note at the top of the DTC
Index
U3000-55 Control Module
Incorrect car
configuration data
received
Check/up-date Car Configuration File using manufacturer
approved diagnostic system
U3000-87 Control Module
Missing message
Check CJB for DTCs and refer to DTC Index.
For additional information, refer to:
Communications Network
(418-00 Module Communications Network, Diagnosis and
Testing).
Check information and entertainment module for Car
Configuration File and MOST network DTCs and refer to relevant
DTC Index. Carry out MOST/CAN network tests using the
manufacturer approved diagnostic system
U3003-16 Battery Voltage
Circuit voltage below
threshold
Carry out pinpoint tests associated with this DTC using the
manufacturer approved diagnostic system
U3003-17 Battery Voltage
Circuit voltage above
threshold
Carry out pinpoint tests associated with this DTC using the
manufacturer approved diagnostic system
General Information - Diagnostic Trouble Code (DTC) IndexDTC: Anti-Lock
Braking System (ABS)
Description and Operation
• NOTE: If a control module or component is suspect and the vehicle remains under manufacturer warranty, refer to the
Warranty Policy and Procedures manual (section B1.2), or determine if any prior approval program is in operation, before
the replacement of a component.
• NOTE: Generic scan tools may not read the codes listed, or may read only 5-digit codes. Match the 5 digits from the scan
tool to the first 5 digits of the 7-digit code listed to identify the fault (the last 2 digits give extra information read by the
manufacturer-approved diagnostic system).
• NOTE: When performing voltage or resistance tests, always use a digital multimeter (DMM) accurate to three decimal
places, and with an up-to-date calibration certificate. W hen testing resistance always take the resistance of the DMM
leads into account.
• NOTE: Check and rectify basic faults before beginning diagnostic routines involving pinpoint tests.
• NOTE: Inspect connectors for signs of water ingress, and pins for damage and/or corrosion.
• NOTE: If DTCs are recorded and, after performing the pinpoint tests, a fault is not present, an intermittent concern may
be the cause. Always check for loose connections and corroded terminals.
Description And Operation
For a detailed description of the anti lock breaking system, refer to the relevant Description and Operation section in the
workshop manual.
For additional information, refer to:
Anti-Lock Control - Stability Assist
(206-09C Anti-Lock Control - Stability Assist,
Description and Operation).
DTC
Description
Possible Cause
Action
B10DF-46 Master cylinder isolation
valve - calibration /
parameter memory failure
Valve not calibrated
- Internal ABS
module failure
Clear DTC and retest if DTC returns. Install a
new ABS module, refer to the new
module/component installation note at the top
of the DTC Index
C0001-01 Master Cylinder Isolation
Valve 1 - electrical failure
Internal ABS module
fault
Clear DTC and retest if DTC returns. Install a
new ABS module, refer to the new
module/component installation note at the top
of the DTC Index
C0002-01 Master Cylinder Isolation
Valve 2 - electrical failure
Internal ABS module
fault
Clear DTC and retest if DTC returns. Install a
new ABS module, refer to the new
module/component installation note at the top
of the DTC Index
C0003-01 Low Pressure Feed Valve 1
- electrical failure
Internal ABS module
fault
Clear DTC and retest if DTC returns. Install a
new ABS module, refer to the new
module/component installation note at the top
of the DTC Index
C0004-01 Low Pressure Feed Valve 2
- electrical failure
Internal ABS module
fault
Clear DTC and retest if DTC returns. Install a
new ABS module, refer to the new
module/component installation note at the top
of the DTC Index
C0010-01 Left Front Inlet Control -
General electrical failure
Internal ABS module
fault
Clear DTC and retest if DTC returns. Install a
new ABS module, refer to the new
module/component installation note at the top
of the DTC Index
C0011-01 Left Front Outlet Control -
General electrical failure
Internal ABS module
fault
Clear DTC and retest if DTC returns. Install a
new ABS module, refer to the new
module/component installation note at the top
of the DTC Index
C0014-01 Right Front Inlet Control -
General electrical failure
Internal ABS module
fault
Clear DTC and retest if DTC returns. Install a
new ABS module, refer to the new
module/component installation note at the top
of the DTC Index
C0015-01 Right Front Outlet Control -
General electrical failure
Internal ABS module
fault
Clear DTC and retest if DTC returns. Install a
new ABS module, refer to the new
module/component installation note at the top
of the DTC Index
C0018-01 Left Rear Inlet Control -
General electrical failure
Internal ABS module
fault
Clear DTC and retest if DTC returns. Install a
new ABS module, refer to the new
module/component installation note at the top
of the DTC Index
DTC
Description
Possible Cause
Action
C0019-01 Left Rear Outlet Control -
General electrical failure
Internal ABS module
fault
Clear DTC and retest if DTC returns. Install a
new ABS module, refer to the new
module/component installation note at the top
of the DTC Index
C001C-01 Right Rear Inlet Control -
General electrical failure
Internal ABS module
fault
Clear DTC and retest if DTC returns. Install a
new ABS module, refer to the new
module/component installation note at the top
of the DTC Index
C001D-01 Right Rear Outlet Control -
General electrical failure
Internal ABS module
fault
Clear DTC and retest if DTC returns. Install a
new ABS module, refer to the new
module/component installation note at the top
of the DTC Index
C0020-01 ABS Pump Motor Control -
General electrical failure
Power supply to
pump motor - short
circuit
Power supply to
pump motor -
incorrect voltage
Pump ground circuit
fault
Mechanical pump
fault
Carry out pinpoint tests associated with this
DTC using the manufacturer approved diagnostic
system. Clear DTC and retest if DTC returns.
Install a new ABS module. Refer to the new
module/component installation note at the top
of the DTC Index
C0020-1C ABS Pump Motor Control -
Circuit voltage out of range
Power supply to
pump motor - short
circuit, high
resistance
Pump ground circuit
fault
Internal ABS module
fault
Carry out pinpoint tests associated with this
DTC using the manufacturer approved diagnostic
system. Clear DTC and retest if DTC returns.
Install a new ABS module. Refer to the new
module/component installation note at the top
of the DTC Index
C0020-71 ABS pump motor control -
actuator stuck
Power supply to
pump motor - short
circuit, high
resistance
Mechanical pump
fault
Carry out pinpoint tests associated with this
DTC using the manufacturer approved diagnostic
system. Clear DTC and retest if DTC returns.
Install a new ABS module. Refer to the new
module/component installation note at the top
of the DTC Index
C0030-07 Left Front Tone Wheel -
Mechanical Failure
Bearing encoder
damaged
Install a new left front wheel bearing.
For additional information, refer to:
Front Wheel
Bearing
(204-01 Front Suspension, Removal and
Installation).
C0031-01 Left Front W heel Speed
Sensor - General electrical
failure
Wheel speed sensor
circuit - short to
ground, short to
power, open circuit
Wheel speed sensor
failure
Carry out pinpoint tests associated with this
DTC using the manufacturer approved diagnostic
system. Clear DTC and retest if DTC returns.
Install a new wheel speed sensor as required.
For additional information, refer to:
Front Wheel
Speed Sensor
(206-09A Anti-Lock Control,
Removal and Installation).
C0031-07 Left Front W heel Speed
Sensor - Mechanical Failure
Wheel speed sensor
faulty/incorrectly
installed
Carry out pinpoint tests associated with this
DTC using the manufacturer approved diagnostic
system. Clear DTC and retest if DTC returns.
Check sensor for correct installation. Install a
new wheel speed sensor as required.
For additional information, refer to:
Front Wheel
Speed Sensor
(206-09A Anti-Lock Control,
Removal and Installation).
C0033-07 Right Front Tone Wheel -
Mechanical Failure
Bearing encoder
damaged
Install a new right front wheel bearing.
For additional information, refer to:
Front Wheel
Bearing
(204-01 Front Suspension, Removal and
Installation).
C0034-01 Right Front Wheel Speed
Sensor - General electrical
failure
Wheel speed sensor
circuit - short to
ground, short to
power, open circuit
Wheel speed sensor
failure
Carry out pinpoint tests associated with this
DTC using the manufacturer approved diagnostic
system. Clear DTC and retest if DTC returns.
Install a new wheel speed sensor as required.
For additional information, refer to:
Front Wheel
Speed Sensor
(206-09A Anti-Lock Control,
Removal and Installation).
C0034-07 Right Front Wheel Speed
Sensor - Mechanical Failure
Wheel speed sensor
faulty/incorrectly
installed
Carry out pinpoint tests associated with this
DTC using the manufacturer approved diagnostic
system. Check sensor for correct installation.
Clear DTC and retest if DTC returns. Install a
new wheel speed sensor as required.
For additional information, refer to:
Front Wheel
Speed Sensor
(206-09A Anti-Lock Control,
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст