Frelander 2. Manual — part 722
Maintenance
166
L
3. Clean the filler cap before removing to
prevent dirt from entering the reservoir.
4. Remove the filler cap.
5. The brake fluid level should be between the
MIN and the MAX marks.
The fluid level may drop slightly during normal
use as a result of brake pad wear but should
not be allowed to drop below the MIN mark.
Topping up the fluid
1. Top-up the reservoir to the MAX mark
using Shell DOT4 ESL brake fluid. If Shell
DOT4 ESL is not available, a low viscosity
DOT4 brake fluid that meets ISO 4925
class 6 and Land Rover LRES22BF03
requirements may be used.
2. Replace the cap.
3. Fit the reservoir cover in the reverse order
of removal.
POWER STEERING FLUID CHECK
Checking the fluid level
Check and top-up the fluid with the vehicle on
level ground, engine switched off, and the
system cold. Ensure that the steering wheel is
not turned after stopping the engine.
CAUTIONS
Brake fluid will damage painted surfaces.
Soak up any spillage with an absorbent
cloth immediately and wash the area with a
mixture of car shampoo and water.
Only use new fluid from an airtight
container (fluid from opened containers
or fluid previously bled from the system will
have absorbed moisture, which will adversely
affect performance, and must not be used).
E84162
WARNINGS
Power steering fluid is highly toxic.
Keep containers sealed and out of reach
of children. If accidental consumption of fluid
is suspected, seek medical attention
immediately.
If the fluid comes into contact with the
skin or eyes, rinse immediately with
plenty of water.
CAUTIONS
The engine must not be started if the fluid
level has dropped below the MIN mark.
Severe damage to the steering pump could
result.
Seek qualified assistance immediately if
there is a noticeable drop in the fluid
level. Severe damage to the steering pump
could result.
If fluid loss is slow, the reservoir may be
topped-up to the upper level mark to
enable the vehicle to be driven to a repair
facility for examination. However, it is
recommended that you seek qualified
assistance before driving the vehicle.
167
Maintenance
R
The level of fluid can be seen through the
translucent body of the reservoir.
The fluid level should be between the MIN and
the MAX marks.
Topping up the fluid
1. Clean the filler cap before removing to
prevent dirt from entering the reservoir.
2. Remove filler cap.
3. Using Pentosin CHF202 fluid, top-up the
reservoir until the fluid level is between the
MIN and MAX marks.
4. Replace filler cap.
WASHER FLUID CHECK
If the quantity of fluid remaining in
the washer reservoir drops to less
than one litre, an amber warning
indicator in the instrument pack will illuminate
or the message LOW WASHER FLUID will be
displayed in the message centre.
CAUTIONS
Power steering fluid will damage painted
surfaces. Soak up any spillage with an
absorbent cloth immediately and wash the
area with a mixture of car shampoo and water.
Do not fill the reservoir above the MAX
mark.
E83619
WARNINGS
Some screen washer products are
inflammable, particularly if high or
undiluted concentrations are exposed to
sparking. Do not allow screen washer fluid to
come into contact with naked flames or
sources of ignition.
If the vehicle is operated in
temperatures below 4°C (40°F), use a
washer fluid with frost protection. In cold
weather, failure to use a washer fluid with frost
protection, could result in impaired vision and
increase the risk of a vehicle crash.
CAUTIONS
Do not use an antifreeze or vinegar/water
solution in the washer reservoir -
antifreeze will damage painted surfaces, while
vinegar can damage the windscreen washer
pump.
Body panels may suffer discolouration as
a result of screen washer fluid spillage.
Take care to avoid spillage, particularly if an
undiluted or high concentration is being used.
If spillage occurs, wash the affected area
immediately with water.
Maintenance
168
L
The washer reservoir supplies both front and
rear screen washer jets and headlamp washer
jets.
Check and top-up the reservoir level at least
every week. Always top-up with screen washer
fluid to prevent freezing.
Operate the washer switches periodically to
check that the nozzles are clear and properly
directed.
Topping up the fluid
1. Clean the filler cap before removing to
prevent dirt from entering the reservoir.
2. Remove filler cap.
3. Top-up the reservoir until the fluid is
visible in the filler neck.
4. Replace filler cap.
Washer reservoir capacity
• Models without headlamp wash - 3.1 litres
(5.45 pints).
• Models with headlamp wash - 5.8 litres
(10.2 pints).
E83620
169
Maintenance
R
TECHNICAL SPECIFICATIONS
Lubricants and fluids
¹ If Shell DOT4 ESL is not available, a low
viscosity DOT4 brake fluid that meets ISO 4925
class 6 and Land Rover LRES22BF03
requirements may be used.
Part
Variant
Specification
Engine oil
Diesel vehicles
SAE 5W-30 meeting Ford
913-B specification.
Engine oil
Petrol vehicles
SAE 0W-30 meeting ACEA A5
or B5 specification.
Main gearbox oil
Manual transmission
Castrol MTF 97309
Main gearbox oil
Automatic transmission
Esso JWS3309US
Power transfer unit fluid
Diesel vehicles
Castrol BOT119
Power transfer unit fluid
Petrol vehicles
Castrol BOT118
Rear differential oil
All vehicles
Castrol EPX
Rear differential on demand
coupler fluid
All vehicles
STAT OIL SL01-301
Power steering fluid
All vehicles
Pentosin CHF202 PAS fluid
Brake fluid
All vehicles
Shell DOT4 ESL ¹
Screen washer
All vehicles
Screen wash with frost
protection
Coolant
All vehicles
50% mixture of Texaco XLC
antifreeze and water.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст