Frelander 2. Manual — part 19
DTC
Description
Possible Cause
Action
Switch internal failure
B1130-88 Light Switch Module -
Bus off
Lost communications with
lighting switch module
Carry out diagnostic strategy associated with this DTC
using manufacturer approved diagnostic system
B1131-88 Wiper Motor Module -
Bus off
Lost communications with
wiper motor module
Carry out diagnostic strategy associated with this DTC
using manufacturer approved diagnostic system
B113C-11 Hazard switch
illumination - circuit
short to ground
Hazard switch illumination
circuit - short to ground
Refer to electrical circuit diagrams and check hazard
switch illumination circuit for short to ground
B113C-15 Hazard switch
illumination - circuit
short to power or
open
Hazard switch illumination
circuit - short to power,
open circuit
Refer to electrical circuit diagrams and check hazard
switch illumination circuit for short to power, open
circuit
B113D-12 Sunroof Global
Open/Close Control -
circuit short to power
Roof opening panel global
open/close control circuit -
short to power
Refer to electrical circuit diagrams and check roof
opening panel global open/close control circuit for short
to power
B113D-14 Sunroof Global
Open/Close Control -
circuit short to ground
or open
Roof opening panel global
open/close control circuit -
short to ground, open
circuit
Refer to electrical circuit diagrams and check roof
opening panel global open/close control circuit for short
to ground, open circuit
B1182-51 Tire Pressure
Monitoring System
(TPMS) - Not
Programmed
TPMS module in
Transport/Factory mode
Enter TPMS module into customer mode using
manufacturer approved diagnostic system
B11BC-11 Extended accessory
relay - circuit short to
ground
Extended accessory relay
circuit - short to ground
Refer to electrical circuit diagrams and check extended
accessory relay circuit for short to ground
B11BC-15 Extended accessory
relay - circuit short to
power or open
Extended accessory relay
circuit - short to power,
open circuit
Refer to electrical circuit diagrams and check extended
accessory relay circuit for short to power, open circuit
B1A79-11 Rear Fog Lamp -
circuit short to ground
Rear fog lamp supply
circuit - short to ground
Refer to electrical circuit diagrams and check rear fog
lamp supply circuit for short to ground
B1A79-13 Rear Fog Lamp -
circuit open
Rear fog lamp supply
circuit - open circuit
Refer to electrical circuit diagrams and check rear fog
lamp supply circuit for open circuit
B1A84-41 Car Configuration
Data - general
checksum failure
Checksum error
Configure the CJB as a 'NEW' module using the
manufacturer approved diagnostic system
B1A99-04 Power On Reset-
System Internal
failure
The DTC will be set if the
reset counter reaches the
maximum value (currently
5)
Install a new CJB, refer to the new module/component
installation note at the top of the DTC Index
B1C96-11 Alarm LED Circuit -
circuit short to ground
Alarm LED circuit - short to
ground
Refer to electrical circuit diagrams and check alarm LED
circuit for short to ground
B1C96-15 Alarm LED Circuit -
circuit short to power
or open
Alarm LED circuit - short to
power, open circuit
Refer to electrical circuit diagrams and check alarm LED
circuit for short to power, open circuit
B1D00-11 Left-hand Low Beam
Circuit - circuit short
to ground
Left-hand low beam circuit
- short to ground
Refer to electrical circuit diagrams and check left-hand
low beam circuit for short to ground
B1D00-13 Left-hand Low Beam
Circuit - circuit open
Left-hand low beam circuit
- open circuit
Refer to electrical circuit diagrams and check left-hand
low beam circuit for open circuit
B1D01-11 Right-hand Low Beam
Circuit - circuit short
to ground
Right-hand low beam
circuit - short to ground
Refer to electrical circuit diagrams and check right-hand
low beam circuit for short to ground
B1D01-13 Right-hand Low Beam
Circuit - circuit open
Right-hand low beam
circuit - open circuit
Refer to electrical circuit diagrams and check right-hand
low beam circuit for open circuit
B1D06-11 Left Turn Indicator -
circuit short to ground
Left turn indicator circuit -
short to ground
Refer to electrical circuit diagrams and check left turn
indicator circuit for short to ground
B1D06-13 Left Turn Indicator -
circuit open
Left turn indicator circuit -
open circuit
Refer to electrical circuit diagrams and check left turn
indicator circuit for open circuit
B1D07-11 Right Turn Indicator -
circuit short to ground
Right turn indicator circuit
- short to ground
Refer to electrical circuit diagrams and check right turn
indicator circuit for short to ground
B1D07-13 Right Turn Indicator -
circuit open
Right turn indicator circuit
- open circuit
Refer to electrical circuit diagrams and check right turn
indicator circuit for open circuit
B1D17-00 Battery Backed
Sounder - General
Failure Information
Internal inclination sensor
fault
Carry out the pinpoint tests associated to this DTC
using the manufacturer approved diagnostic system
DTC
Description
Possible Cause
Action
B1D17-88 Battery Backed
Sounder - bus off
Lost communications with
battery backed sounder
Carry out the network test associated with this DTC
using the manufacturer approved diagnostic system
B1D17-96 Battery Backed
Sounder - component
internal failure
Battery backed sounder -
internal failure
Install a new battery backed sounder, refer to new
module/component installation note at the top of the
DTC Index
B1D18-96 Volumetric Sensor
Circuit - component
internal failure
Interior motion sensor -
internal failure
Install a new interior motion sensor, refer to new
module/component installation note at the top of the
DTC Index
B1D21-62 Remote Control
Switch - Signal
compare failure
A request from a
programmed remote key
was received and the
rolling counter was
incorrect
Re-synchronise the remote key by using the key to
start the vehicle
B1C55-12 Horn Relay Coil
Circuit - circuit short
to power
Horn relay control circuit -
short to power
Refer to electrical circuit diagrams and check horn relay
control circuit for short to power
B1C55-14 Horn Relay Coil
Circuit- circuit short
to ground or open
Horn relay control circuit -
short to ground, open
circuit
Refer to electrical circuit diagrams and check horn relay
control circuit for short to ground, open circuit
B1C82-12 Headlamp W asher
Relay Coil Circuit -
circuit short to power
Headlamp washer relay
control circuit - short to
power
Refer to electrical circuit diagrams and check headlamp
washer relay control circuit for short to power
B1C82-14 Headlamp W asher
Relay Coil Circuit -
circuit short to ground
or open
Headlamp washer relay
control circuit - short to
ground, open circuit
Refer to electrical circuit diagrams and check headlamp
washer relay control circuit for short to ground, open
circuit
B1C84-12 Heated Rear Window
Relay Output Circuit -
circuit short to power
Heated rear window relay
control circuit - short to
power
Refer to electrical circuit diagrams and check heated
rear window relay control circuit for short to power
B1C84-14 Heated Rear Window
Relay Output Circuit -
circuit short to ground
or open
Heated rear window relay
control circuit - short to
ground, open circuit
Refer to electrical circuit diagrams and check heated
rear window relay control circuit for short to ground,
open circuit
B1C90-12 Auxiliary Driving
Lamps Relay Coil
Circuit - circuit short
to power
Auxiliary driving lamps
relay control circuit - short
to power
Refer to electrical circuit diagrams and check auxiliary
driving lamps relay control circuit for short to power
B1C90-14 Auxiliary Driving
Lamps Relay Coil
Circuit - circuit short
to ground or open
Auxiliary driving lamps
relay control circuit - short
to ground, open circuit
Refer to electrical circuit diagrams and check auxiliary
driving lamps relay control circuit for short to ground,
open circuit
B1D13-12 Interior Lights #1
Circuit - circuit short
to power
Instrument panel interior
lights circuit - short to
power
Refer to electrical circuit diagrams and check
instrument panel interior lights circuit for short to
power
B1D13-14 Interior Lights #1
Circuit - circuit short
to ground or open
Instrument panel interior
lights circuit - short to
ground, open circuit
Refer to electrical circuit diagrams and check
instrument panel interior lights circuit for short to
ground, open circuit
B1D1A-12 Interior Lights Circuit
'C' - circuit short to
power
Roof console interior lights
circuit - short to power
Refer to electrical circuit diagrams and check roof panel
interior lights circuit for short to power
B1D1A-14 Interior Lights Circuit
'C' - circuit short to
ground or open
Roof console interior lights
circuit - short to ground,
open circuit
Refer to electrical circuit diagrams and check roof panel
interior lights circuit for short to ground, open circuit
B1D35-24 Hazard Switch -
Signal stuck high
Hazard switch is active
more than 60 seconds
Carry out the pinpoint tests associated to this DTC
using the manufacturer approved diagnostic system
C0023-11 Stop Lamp Control -
circuit short to ground
Stop lamp control circuit -
short to ground
Refer to electrical circuit diagrams and check stop lamp
control circuit for short to ground
C0023-13 Stop Lamp Control -
circuit open
Stop lamp control circuit -
open circuit
Refer to electrical circuit diagrams and check stop lamp
control circuit for open circuit
C1108-11 Pedal Sensor(s)
Supply Voltage -
circuit short to ground
Pedal sensor(s) supply
voltage circuit - short to
ground
Refer to electrical circuit diagrams and check pedal
sensor(s) supply voltage circuit for short to ground
C1108-15 Pedal Sensor(s)
Supply Voltage -
circuit short to power
or open
Pedal sensor(s) supply
voltage circuit - short to
power, open circuit
Refer to electrical circuit diagrams and check pedal
sensor(s) supply voltage circuit for short to power,
open circuit
C1A41-21 Clutch Pedal Sensor -
signal amplitude <
minimum
signal<3% of supply(5V)
Carry out the pinpoint tests associated to this DTC
using the manufacturer approved diagnostic system
DTC
Description
Possible Cause
Action
C1A41-22 Clutch Pedal Sensor -
signal amplitude >
maximum
signal>=97% of
supply(5V)
Carry out the pinpoint tests associated to this DTC
using the manufacturer approved diagnostic system
C1A56-16 Front Left W heel
Module - circuit
voltage below
threshold (low
battery)
Siemens internal algorithm Carry out the pinpoint tests associated to this DTC
using the manufacturer approved diagnostic system
C1A56-86 Front Left W heel
Module - signal
invalid (out of range)
Siemens internal algorithm Carry out the pinpoint tests associated to this DTC
using the manufacturer approved diagnostic system
C1A56-93 Front Left W heel
Module - no operation
(lost sensor)
Siemens internal algorithm Carry out the pinpoint tests associated to this DTC
using the manufacturer approved diagnostic system
C1A57-11 Left Front Initiator -
short to ground
Left front initiator circuit -
short to ground
Refer to electrical circuit diagrams and check left front
initiator circuit for short to ground
C1A57-12 Left Front Initiator -
short to power
Left front initiator circuit -
short to power
Refer to electrical circuit diagrams and check left front
initiator circuit for short to power
C1A57-13 Left Front Initiator -
open circuit
Left front initiator circuit -
open circuit
Refer to electrical circuit diagrams and check left front
initiator circuit for open circuit
C1A58-16 Front Right W heel
Module - circuit
voltage below
threshold (low
battery)
Siemens internal algorithm Carry out the pinpoint tests associated to this DTC
using the manufacturer approved diagnostic system
C1A58-86 Front Right W heel
Module - signal
invalid (out of range)
Siemens internal algorithm Carry out the pinpoint tests associated to this DTC
using the manufacturer approved diagnostic system
C1A58-93 Front Right W heel
Module - no operation
(lost sensor)
Siemens internal algorithm Carry out the pinpoint tests associated to this DTC
using the manufacturer approved diagnostic system
C1A59-11 Right Front Initiator -
short to ground
Right front initiator circuit
- short to ground
Refer to electrical circuit diagrams and check right front
initiator circuit for short to ground
C1A59-12 Right Front Initiator -
short to power
Right front initiator circuit
- short to power
Refer to electrical circuit diagrams and check right front
initiator circuit for short to power
C1A59-13 Right Front Initiator -
open circuit
Right front initiator circuit
- open circuit
Refer to electrical circuit diagrams and check right front
initiator circuit for open circuit
C1A60-16 Rear Left Wheel
Module - circuit
voltage below
threshold (low
battery)
Siemens internal algorithm Carry out the pinpoint tests associated to this DTC
using the manufacturer approved diagnostic system
C1A60-86 Rear Left Wheel
Module - signal
invalid (out of range)
Siemens internal algorithm Carry out the pinpoint tests associated to this DTC
using the manufacturer approved diagnostic system
C1A60-93 Rear Left Wheel
Module - no operation
(lost sensor)
Siemens internal algorithm Carry out the pinpoint tests associated to this DTC
using the manufacturer approved diagnostic system
C1A61-11 Left Rear Initiator -
short to ground
Left rear initiator circuit -
short to ground
Refer to electrical circuit diagrams and check left rear
initiator circuit for short to ground
C1A61-12 Left Rear Initiator -
short to power
Left rear initiator circuit -
short to power
Refer to electrical circuit diagrams and check left rear
initiator circuit for short to power
C1A61-13 Left Rear Initiator -
open circuit
Left rear initiator circuit -
open circuit
Refer to electrical circuit diagrams and check left rear
initiator circuit for open circuit
C1A62-16 Rear Right Wheel
Module - circuit
voltage below
threshold (low
battery)
Siemens internal algorithm Carry out the pinpoint tests associated to this DTC
using the manufacturer approved diagnostic system
C1A62-86 Rear Right Wheel
Module - signal
invalid (out of range)
Siemens internal algorithm Carry out the pinpoint tests associated to this DTC
using the manufacturer approved diagnostic system
C1A62-93 Rear Right Wheel
Module - no operation
(lost sensor)
Siemens internal algorithm Carry out the pinpoint tests associated to this DTC
using the manufacturer approved diagnostic system
C1A63-11 Right Rear Initiator -
short to ground
Right rear initiator circuit -
short to ground
Refer to electrical circuit diagrams and check right rear
initiator circuit for short to ground
C1A63-12 Right Rear Initiator -
short to battery
Right rear initiator circuit -
short to power
Refer to electrical circuit diagrams and check right rear
initiator circuit for short to power
DTC
Description
Possible Cause
Action
C1A63-13 Right Rear Initiator -
open circuit
Right rear initiator circuit -
open circuit
Refer to electrical circuit diagrams and check right rear
initiator circuit for open circuit
C1B14-12 Sensor supply #1 -
circuit short to power
Sensor supply #1 circuit -
short to power
Refer to electrical circuit diagrams and check sensor
supply #1 circuit for short to power
C1D18-00 Localisation failed
Tire pressure monitor
localisation failed
Check for additional related DTCs and refer to this DTC
Index
C1D21-05 Wheel module -
general signal failure
Siemens internal algorithm Carry out the pinpoint tests associated to this DTC
using the manufacturer approved diagnostic system
C1D22-49 Steering W heel
Switch Right Module -
Internal failure
Steering wheel switch right
module - internal failure
Install a new wash/wipe switch, refer to new
module/component installation note at the top of the
DTC Index
C2003-07 Steering W heel
Switch Left Module -
Mechanical Failures
Steering wheel switch left
module - mechanical
failure
Install a new indicator switch, refer to new
module/component installation note at the top of the
DTC Index
C2003-49 Steering W heel
Switch Left Module -
Internal failure
Steering wheel switch left
module - internal failure
Install a new indicator switch, refer to new
module/component installation note at the top of the
DTC Index
C2004-12 Headlamp washer
relay B - circuit short
to power
Headlamp washer relay B
circuit - short to power
Refer to electrical circuit diagrams and check headlamp
washer relay B circuit for short to power
C2004-14 Headlamp washer
relay B - circuit short
to ground or open
Headlamp washer relay B
circuit - short to ground,
open circuit
Refer to electrical circuit diagrams and check headlamp
washer relay B circuit for short to ground, open circuit
P0460-15 Fuel Level Sensor A -
short to battery or
open circuit
Fuel tank unit circuit A
short to power, open
circuit
• NOTE: Carry out pinpoint tests associated with this
DTC using the manufacturer approved diagnostic
system
Refer to the electrical circuit diagrams and check the
circuit between the central junction box and the fuel
tank unit circuit (F/P sensor) for short to power, open
circuit. Using the manufacturer approved diagnostic
system check and install latest relevant level of
software to the central junction box and the instrument
panel cluster. If the level of software is correct carry
out a battery reset
P0462-00 Fuel Level Sensor A -
no subtype
information
Fuel tank unit circuit A
short to ground or high
resistance
• NOTE: Carry out pinpoint tests associated with this
DTC using the manufacturer approved diagnostic
system
Refer to the electrical circuit diagrams and check the
circuit between the central junction box and the fuel
tank unit circuit (F/P sensor) for short to ground. Using
the manufacturer approved diagnostic system check
and install latest relevant level of software to the
central junction box and the instrument panel cluster.
If the level of software is correct carry out a battery
reset
P0604-00 Internal Control
Module Random
Access Memory (RAM)
Error
RAM Checksum not correct Install a new CJB, refer to the new module/component
installation note at the top of the DTC Index
P0605-00 Internal Control
Module Read Only
Memory (ROM) Error
ROM Checksum not correct Install a new CJB, refer to the new module/component
installation note at the top of the DTC Index
P062F-00 Internal Control
Module Read Only
Memory (ROM) Error
EEP read back value does
not match written value
Install a new CJB, refer to the new module/component
installation note at the top of the DTC Index
P0801-11 Reverse inhibit
control circuit - circuit
short to ground
Reverse inhibit control
circuit - short to ground
Refer to electrical circuit diagrams and check reverse
inhibit control circuit for short to ground
P1346-13 Fuel Level Sensor B -
open circuit
Fuel tank unit circuit B
short to power, open
circuit
• NOTE: Carry out pinpoint tests associated with this
DTC using the manufacturer approved diagnostic
system
Refer to the electrical circuit diagrams and check the
circuit between the central junction box and the fuel
tank unit circuit (Fuel eject sensor) for short to power,
open circuit. Using the manufacturer approved
diagnostic system check and install latest relevant
level of software to the central junction box and the
instrument panel cluster. If the level of software is
correct carry out a battery reset
P1348-00 Fuel Level Sensor B -
no subtype
information
Fuel tank unit circuit B
short to ground
• NOTE: Carry out pinpoint tests associated with this
DTC using the manufacturer approved diagnostic
system
Refer to the electrical circuit diagrams and check the
circuit between the central junction box and the fuel
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст