Defender. Manual — part 134
Starter motor
fitment/casing
flywheel/drive plate ring gear teeth for damage, foreign objects, etc.
DTC Index
• NOTE: If a control module or component is suspect and the vehicle remains under manufacturer warranty, refer to the
Warranty Policy and Procedures manual (section B1.2), or determine if any prior approval program is in operation,
before the replacement of a component.
• NOTE: Generic scan tools may not read the codes listed, or may read only 5-digit codes. Match the 5 digits from the
scan tool to the first 5 digits of the 7-digit code listed to identify the fault (the last 2 digits give extra information read
by the manufacturer-approved diagnostic system).
• NOTE: When performing voltage or resistance tests, always use a digital multimeter (DMM) accurate to three decimal
places, and with an up-to-date calibration certificate. When testing resistance always take the resistance of the DMM
leads into account.
• NOTE: Check and rectify basic faults before beginning diagnostic routines involving pinpoint tests.
• NOTE: Inspect connectors for signs of water ingress, and pins for damage and/or corrosion.
• NOTE: If DTCs are recorded and, after performing the pinpoint tests, a fault is not present, an intermittent concern
may be the cause. Always check for loose connections and corroded terminals.
• NOTE: For a full list of engine control module (ECM) DTCs:
REFER to:
Electronic Engine Controls
(303-14 Electronic Engine Controls - 2.4L Duratorq-TDCi HPCR (103kW/140PS) -
Puma, Diagnosis and Testing).
DTC
Description
Possible causes
Action
P061512 Starter relay
circuit - circuit
short to battery
Starter relay
circuit: short
circuit to
power
Check the starter relay circuits. Refer to the electrical guides. Rectify
as necessary. Clear the DTCs and test for normal operation.
P061514 Starter relay
circuit - circuit
short to ground or
open
Starter relay
circuit: short
circuit to
ground
Starter relay
circuit: open
circuit
P160231 Immobilizer/engine
control module
(ECM)
communication
error – no signal
Alarm
(immobilizer)
- instrument
cluster
circuit: short
circuit to
ground
Alarm
(immobilizer)
- instrument
cluster
circuit: short
circuit to
power
Alarm
(immobilizer)
- instrument
cluster
circuit: open
circuit
Engine
control
module
(ECM) fault
Instrument
cluster fault
Check for related DTCs. Rectify as necessary. Clear the DTCs and test
for normal operation. Check the alarm (immobilizer) circuits. Refer to
the electrical guides. Rectify as necessary. Clear the DTCs and test for
normal operation. Refer to the warranty policy and procedures manual
if a module is suspect.
Starting System - 2.4L Duratorq-TDCi HPCR (103kW/140PS) - Puma -
Starter Motor
Removal and Installation
Removal
1. Disconnect the battery ground cable.
For additional information, refer to:
Battery Disconnect and
Connect
(414-01 Battery, Mounting and Cables, General
Procedures).
2.
WARNING: Do not work on or under a vehicle
supported only by a jack. Always support the vehicle on safety
stands.
Raise and support the vehicle.
For additional information, refer to:
Lifting
(100-02 Jacking
and Lifting, Description and Operation).
3. Remove the fuel line support bracket.
Remove the nut.
4. Release the starter motor wiring harness clip.
5. Release the 2 battery positive cables and the switch lead
from the starter motor solenoid.
1. Remove the battery positive cable nut.
2. Release the starter motor switch lead nut.
6. Remove the starter motor lower bolt.
6. Remove the starter motor lower bolt.
7. Remove the starter motor.
Installation
1. Install the starter motor.
Tighten to 35 Nm (26 lb.ft).
2. Tighten to 35 Nm (26 lb.ft).
3. Secure the 2 battery positive cables and the switch lead to
3. Secure the 2 battery positive cables and the switch lead to
the starter motor solenoid.
1. Tighten to 12 Nm (9 lb.ft).
2. Tighten to 8 Nm (6 lb.ft).
4. Secure the starter motor wiring harness clip.
5. Install the fuel line support bracket.
Tighten to 8 Nm (6 lb.ft).
6. Connect the battery ground cable.
For additional information, refer to:
Battery Connect
(414-01
Battery, Mounting and Cables, General Procedures).
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст