Range Rover Classic. Manual — part 182
86
ELECTRICAL
16
REPAIR
AUXILIARY SWITCHES AND BULBS
Service repair no - 86.45.49 - Switches
Service repair no - 86.45.29 - Bulbs
The auxiliary switch panel contains up to six switches
depending on vehicle specification. Each switch
incorporates integral symbols for identification.
Unused switch openings are fitted with blank covers,
which are removable, to facilitate fitting extra switches
if required.
The symbols are illuminated by two bulbs which
become operational when vehicle lights are on.
Switch replacement
Remove
1. Disconnect battery negative lead.
2. Remove air suspension switch panel.
See Air
Suspension Switches and Bulbs
3. Carefully prise auxiliary switch panel out of
fascia.
4. Withdraw switch panel as far as electrical leads
will permit.
5. Noting their fitted position, disconnect
multiplug(s) from the switch(es).
6. Depress small retaining lugs on top and bottom
of switch and push switch(es) through front of
switch surround.
Bulb replacement
7. Identify bulb to be replaced and remove
appropriate switch.
8. Rotate bulb holder 90 deg. and withdraw it from
switch; discard bulb holder and bulb.
Refit
9. Reverse removal procedure.
ELECTRICAL
17
REPAIR
AIR SUSPENSION SWITCHES AND BULBS
Service repair no - 86.65.88 - Switches
Service repair no - 86.45.29 - Bulbs
Switch replacement
Remove
1. Disconnect battery negative lead.
2. Carefully release lower edge of panel from
surround, withdraw panel.
3. Noting their fitted positions, disconnect
multiplugs from switches.
4. Depress retaining lugs on switches, remove
switches from panel.
Bulb replacement
5. Identify bulb to be replaced and remove
appropriate switch.
6. Rotate bulb holder 90 deg. and withdraw it from
switch.
Refit
7. Reverse removal procedure.
86
ELECTRICAL
18
REPAIR
HEADLAMP/FLASHER SWITCH AND
WINDSCREEN WASH/WIPE SWITCH
Service repair no - 84.15.34 - Wash wipe switch
Service repair no - 86.65.41 - Headlamp/flasher
switch
NOTE: The following procedure applies to
either switch.
Remove
1. Remove steering column shroud.
See
STEERING, Repair, Steering Column Shroud
2. Position steering wheel for access.
3. Remove 2 screws securing switch.
4. Insert a suitable, flat bladed tool between switch
and casing, depress raised ’pip’, release switch
from casing.
5. Disconnect switch multiplugs.
Refit
6. Connect switch multiplugs.
7. Position switch to casing ensuring ’pip’ is
engaged.
8. Reverse removal procedure. 1 and 3.
HAZARD WARNING SWITCH AND BULB
Service repair no - 86.65.50 - Switch
Service repair no - 86.45.29 - Bulb
Switch replacement
Remove
1. Disconnect battery negative lead.
2. Remove ashtray.
3. Carefully release panel from fascia.
4. Disconnect multiplug from switch.
5. Depress retaining lugs, remove switch from
panel.
Bulb replacement
6. Rotate bulb holder 90 deg. and withdraw it from
switch, discard bulb holder and bulb.
Refit
7. Reverse removal procedure.
ELECTRICAL
19
REPAIR
IGNITION/STARTER SWITCH - BULB
REPLACEMENT
Service repair no - 86.45.29
Remove
1. Remove steering column shroud.
See
STEERING, Repair, Steering Column Lock
Assembly
2. Withdraw bulb holder, remove bulb.
Refit
3. Reverse removal procedure.
DOOR PILLAR SWITCH
Service repair no - 86.65.15
Remove
1. Disconnect battery negative lead.
2. Remove screw securing switch to door pillar.
3. Remove switch.
4. Disconnect electrical lead from connector blade.
Refit
5. Reverse removal procedure.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст