Freelander Body Repair Manual — part 29
BODY
14
DOORS
Do not carry out further dismantling if
component is removed for access only.
12. Remove 7 trim studs from casing.
13. Remove 4 Torx screws securing door pocket.
14. Remove door pocket.
15. Remove 4 Torx screws from door pull.
16. Remove door pull.
17. Remove 4 Torx screws from door speaker
grille.
18. Remove speaker grille.
19. Release retainer and remove sill button guide.
20. Fit sill button guide to replacement casing and
secure with retainer.
21. Fit speaker grille to replacement casing and
secure with Torx screws.
22. Fit door pull to replacement casing and secure
with Torx screws.
23. Fit door pocket to replacement casing and
secure with Torx screws.
24. Fit trim studs to replacement casing.
Refit
1. Position casing to door and engage trim studs.
2. Fit screws securing door pocket.
3. Fit cup holder.
4. Fit door pull.
5. Position door release escutcheon and secure
with screw.
6. Connect Lucars to tweeter speaker.
7. Fit cheater panel.
BODY
DOORS
15
CASING - REAR DOOR
Service repair no - 76.34.04
Remove
1. Remove clip from window winder handle,
remove handle and escutcheon.
2. Remove screw securing door release
escutcheon.
3. Push escutcheon in and to the rear of door to
release from securing catch, remove
escutcheon.
4. Remove 2 screws from door pull.
5. Release 10 trim studs.
6. Remove casing.
Do not carry out further dismantling if
component is removed for access only.
7. Remove 4 Torx screws from door pull, and
remove door pull.
8. Remove 4 Torx screws from speaker grille and
remove grille.
9. Release retainer and remove sill button guide.
10. Remove 10 trim studs.
11. Fit trim studs to replacement trim casing.
12. Fit sill button guide to replacement casing and
secure with retainer.
13. Fit speaker grille to replacement casing and
secure with Torx screws.
14. Fit door pull to replacement casing and secure
with Torx screws.
Refit
1. Position casing to door and engage trim studs.
2. Fit door pull screws.
3. Position door release escutcheon and secure
with screw.
4. Fit window winder escutcheon and window
winder and secure with clip.
BODY
16
DOORS
CASING - TAIL DOOR
Service repair no - 76.34.10
Remove
1. Remove 4 screws securing bottom of casing.
2. Release 7 clips securing sides and bottom of
casing.
3. Release 5 clips securing top of casing.
4. Remove casing.
5. Remove 7 trim studs.
Refit
1. Ensure trim studs are in position.
2. Position casing and secure in top clips.
3. Secure clips on side and bottom of casing.
4. Fit screws to bottom of casing.
BODY
DOORS
17
WATER SHEDDER - LOWER - 3 DOOR
Service repair no - 76.34.18
NOTE: Always replace a damaged water
shedder.
Remove
1. Remove front door pocket.
See this section.
2. Release and discard water shedder.
Refit
1. Clean door contact area with white spirit.
2. Position NEW water shedder to door and seal
in position, by applying hand pressure to centre
bottom of shedder first then move out from this
point in both directions applying an even
pressure to the seal, smooth out any creases.
CAUTION: It is crucial that no creases are
present along the base of the water
shedder.
NOTE: To obtain an effective seal when
fitting a new water shedder, ensure that
the water shedder and door contact
surface are at room temperature: 18
°
C to 30
°
C.
3. Fit front door pocket.
See this section.
POCKET - FRONT DOOR - 3 DOOR
Service repair no - 76.34.19
Remove
1. Remove 8 Torx screws securing pocket to door
and remove pocket.
Refit
1. Position pocket, fit and tighten Torx screws.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст