Freelander Body Repair Manual — part 23
RESTRAINT SYSTEMS
REPAIRS
7
SEAT BELT BUCKLE - REAR - 5 DOOR
Service repair no - 76.73.32
Remove
1. Position rear seat forward.
2. Remove 3 screws from end cover and remove
covers from seat hinges.
3. Remove 4 Torx bolts from seat lock down
catch and remove catch assembly.
4. Remove Torx bolt from seat belt buckle and
remove buckle.
Refit
1. Fit buckle to catch assembly and tighten Torx
bolt to 40 Nm.
2. Fit catch assembly to seat and tighten Torx
bolts.
3. Fit end cover and tighten screws.
4. Reposition seat.
PRETENSIONER - SEAT BELT - FRONT
Service repair no - 76.73.75
Remove
WARNING:
See GENERAL INFORMATION,
SRS Precautions.
1. Make the SRS system safe.
See GENERAL
INFORMATION, SRS Precautions.
2. Remove rear console.
See BODY, Interior
trim components.
3. Disconnect and secure pretensioner multiplug.
4. Remove Torx bolt from pretensioner, release
pretensioner from seat location and remove
pretensioner assembly.
WARNING: Store the pretensioner in
accordance with the storage procedures.
See GENERAL INFORMATION, SRS
Precautions.
RESTRAINT SYSTEMS
8
REPAIRS
Refit
NOTE: If the pretensioner is to be
replaced, the bar code of the new
pretensioner must be recorded.
1. Position pretensioner in seat location and
tighten Torx bolt to 32 Nm.
2. Connect and secure pretensioner multiplug.
3. Fit rear console.
See BODY, Interior trim
components.
4. Connect battery leads, earth lead last.
5. Carry out system check by turning the ignition
on and checking that the SRS warning lamp
illuminates, then extinguishes after
approximately 5 seconds.
SEAT BELT BUCKLE - CENTRE - REAR - 5
DOOR
Service repair no - 76.73.98
Remove
1. Remove RH rear seat.
See BODY, Seats and
seat belts.
2. Remove 2 screws and remove seat belt reel
cover.
RESTRAINT SYSTEMS
REPAIRS
9
3. Remove nut and release seat belt reel.
4. Remove 5 screws and remove both end covers
from seat hinges.
5. Remove 3 Torx bolts and remove squab from
cushion.
6. Release rear of cushion cover from frame.
7. Release sides and front of cushion cover from
frame.
8. Release cover and pad from frame.
9. Remove Torx bolt from seat belt buckle and
remove buckle.
RESTRAINT SYSTEMS
10
REPAIRS
Refit
1. Position seat belt buckle and tighten Torx bolt
to 40 Nm.
2. Fit cover and pad to frame.
3. Fit front and sides of cushion cover to frame.
4. Fit rear of cushion cover to frame.
5. Fit cushion to squab and tighten Torx bolts.
6. Fit end covers and tighten screws.
7. Position seat belt reel and tighten nut to 32
Nm.
8. Fit seat belt reel cover and tighten screws.
9. Fit rear seat.
See BODY, Seats and seat
belts.
AIRBAG - STEERING WHEEL
Service repair no - 76.74.01
Remove
WARNING:
See GENERAL INFORMATION,
SRS Precautions.
1. Make the SRS system safe.
See GENERAL
INFORMATION, SRS Precautions.
2. Remove 2 Torx bolts securing the airbag
module to steering wheel.
3. Release airbag module from steering wheel.
CAUTION: Do not allow the airbag module
to hang by the harness.
4. Disconnect harness connector from the airbag
module.
5. Remove airbag module.
WARNING: Store the airbag module in
accordance with the storage procedures.
See GENERAL INFORMATION, SRS
Precautions.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст