Freelander Body Repair Manual — part 40
BODY
INTERIOR TRIM COMPONENTS
7
FINISHER -’B/C’ POST LOWER - 5 DOOR
Service repair no - 76.13.29
Remove
1. Remove cushion side finisher.
See Seats and
seat belts.
2. Remove scrivet and 5 Torx screws from carpet
retainer.
3. Remove front carpet retainer.
4. Release B/C’ post upper finisher and position
aside.
5. Remove 3 Torx screws from top of seat base
finisher.
6. Remove scrivet from front of B/C’ post lower
finisher.
7. Remove Torx screw from rear of B/C’ post
lower finisher.
8. Release and remove B/C’ post lower finisher
from seat base finisher.
Refit
1. Locate B/C’ post lower finisher under seat
base finisher and rear carpet retainer.
2. Fit Torx screw to rear of B/C’ post lower
finisher.
3. Fit scrivet to B/C’ post lower finisher.
4. Fit Torx screws to seat base finisher.
5. Align and secure B/C’ post upper finisher.
6. Fit cushion side finisher.
See Seats and seat
belts.
7. Fit front carpet retainer and secure with Torx
screws and scrivet.
BODY
8
INTERIOR TRIM COMPONENTS
CASING - BODY SIDE - REAR
Service repair no - 76.13.57
Remove
1. Remove rear seat.
See Seats and seat belts.
2. Remove Torx bolt securing rear seat belt lower
to body and position seat belt aside.
3. Release 6 trim clips and remove trim casing.
4. Remove 6 trim fasteners from body panel.
Do not carry out further dismantling if
component is removed for access only.
5. Noting the position of the 3 long screws,
remove 10 Torx screws and remove pocket
from trim casing.
6. Remove 3 screws and remove pocket finisher.
7. Release 6 tags and remove speaker grille.
8. Position speaker grille on replacement casing
and secure tags.
9. Position pocket finisher and tighten screws.
10. Position pocket and tighten Torx screws
Refit
1. Fit trim fasteners to trim casing.
2. Position trim casing and secure clips.
3. Position seat belt and tighten Torx bolt to 50
Nm.
4. Fit rear seat.
See Seats and seat belts.
BODY
INTERIOR TRIM COMPONENTS
9
CONSOLE - FRONT
Service repair no - 76.25.01
Remove
1. Remove rear console.
See this section.
2. Remove radio.
See ELECTRICAL, Repairs.
3. Remove 3 heater control knobs.
4. Remove 2 screws from heater control panel.
5. Remove heater control panel.
6. Release tags and remove radio cage.
7. Remove 2 screws from top of console.
8. Remove 4 screws securing switch pack to
console.
9. Remove 3 screws from centre and sides of
console.
10. Release 5 multiplugs and bulb holder from
switch pack.
11. Remove console.
BODY
10
INTERIOR TRIM COMPONENTS
12. Remove 4 screws from switch pack assembly
and remove assembly.
Refit
1. Position switch pack assembly, fit and tighten
screws.
2. Position console to fascia.
3. Connect multiplugs and bulb holder to switch
pack.
4. Fit and tighten screws securing centre and
sides of console.
5. Fit and tighten screws securing switch pack to
console.
6. Fit and tighten screws to top of console.
7. Position radio cage to console and secure with
retaining tags.
8. Position heater control panel, fit and tighten
screws.
9. Fit heater control knobs.
10. Fit radio.
See ELECTRICAL, Repairs.
11. Fit rear console.
See this section.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст