Jeep Wrangler JK (2018 year). Instruction — part 9
CAUTION! (Continued)
• Careless handling and storage of the soft top may
damage the seals, causing water to leak into the
vehicle’s interior.
• The soft top must be positioned properly to ensure
sealing. Improper installation can cause water to leak
into the vehicle’s interior.
NOTE:
Do not remove any of the three attachment knobs
unless you are planning on installing the hard top.
Quick Steps For Lowering The Soft Top
1. Remove the side windows.
Attachment Knobs
Step One
3
GETTING TO KNOW YOUR VEHICLE
131
2. Remove the back window.
NOTE:
Start zipper from the right side to remove back
window.
3. Release header latches from the windshield frame.
Step Two
Step Three
132
GETTING TO KNOW YOUR VEHICLE
4. Release the sail panel retainers from the body side
channel at the rear corners of the vehicle.
NOTE:
When releasing the sail panel retainers, it is helpful
to pull down on the rear roof bow.
5. Fold the sail panels so that they rest on top of the soft
top.
Step Four
Step Five
3
GETTING TO KNOW YOUR VEHICLE
133
6. Fold header rearward, pulling the fabric to the rear.
7. Release Sunrider latch (both sides).
Step Six
Step Six
134
GETTING TO KNOW YOUR VEHICLE
8. Open the swing gate and lower the top.
NOTE:
Ensure the fabric does not overhang the sides of the
vehicle.
Step Seven
Step Eight
3
GETTING TO KNOW YOUR VEHICLE
135
Quick Steps For Raising The Soft Top
1. Open the swing gate and raise the top, engaging the
Sunrider latches (another person may be needed to help
with this operation).
Step One
Step One
136
GETTING TO KNOW YOUR VEHICLE
2. Install rear corner panels.
3. Rotate the header forward.
Step Two
Step Three
3
GETTING TO KNOW YOUR VEHICLE
137
4. Engage the header latches.
5. Install the back window.
Step Four
Step Five
138
GETTING TO KNOW YOUR VEHICLE
6. Install the side windows.
7. To install the side windows, affix the window tempo-
rarily by attaching to the Velcro in the rear corner. Start
the zipper but close only about 1 inch (2.5 cm).
Step Six
Step Seven
3
GETTING TO KNOW YOUR VEHICLE
139
8. Insert the front retainer of the window into the door
channel, making sure the retainer is fully seated and
properly positioned on the door frame. Failure to do so
can result in wind and water leaks or damage to the
window.
9. Insert the retainer along the bottom edge of the window
into the bottom side channel, beginning at the front and
working to the rear of the vehicle. Finish by closing the
zipper completely and attaching the Velcro along the top
and rear of the window. Repeat this step for the opposite
side.
Retainer Insertion
1 — Incorrect Insertion
2 — Correct Insertion
Step Nine
140
GETTING TO KNOW YOUR VEHICLE
Folding Down The Soft Top
Side View Top And Components
1 — 4– Bow
6 — Quarter Window
2 — 3–Bow
7 — Body Side Retainer
3 — 2–Bow
8 — Bottom Retainer — Quarter Window
4 — Header Bow
9 — Sail Panel
5 — Front Retainer — Quarter Window
10 — Check Strap
3
GETTING TO KNOW YOUR VEHICLE
141
Rear View Top And Components
1 — Sail Panels
2 — Zipper Finish
3 — Swing Gate Bar
4 — Zipper Start
5 — Swing Gate Brackets
142
GETTING TO KNOW YOUR VEHICLE
NOTE:
Clean side and rear windows before removal to
assist in preventing scratching during removal of the soft
top. If zippers are difficult to operate due to road dust, etc.,
clean them with a mild soap solution and a small brush.
Cleaning products are available through your authorized
dealer.
1. If your vehicle has half-doors, remove each half-door
window by opening the door and lifting the half-door
window out.
NOTE:
Stow half-door windows carefully outside of the
vehicle, never inside, to avoid scratches.
2. Unclip and move the sun visors to the side.
3. Release the header latches and hooks from the loops on
the windshield frame.
Step Three
3
GETTING TO KNOW YOUR VEHICLE
143
4. Open the swing gate.
5. Before unzipping the rear window, release the first 3
inches (7.6 cm) of both sail panels from the channel.
Remove the swing gate bar by pulling it straight rear-
ward out of the swing gate brackets.
6. Unzip the rear window starting at the right lower corner
of the window. Pull the zipper up, across the top and
down to the left lower corner. Zipper pulls will stay on
the rear window.
Pull down on the rear window to
disengage it from the zipper on the top cover.
Step Five
Step Six
144
GETTING TO KNOW YOUR VEHICLE
7. Remove the rear window retainer from the swing gate
bracket on both the left and right sides.
8. Stow the windows carefully to avoid scratching.
9. Undo the Velcro that runs along the top and rear edge of
the side window.
10. Beginning from the rear lower corner, completely un-
zip the window.
Step Seven
Step Ten
3
GETTING TO KNOW YOUR VEHICLE
145
11. Once unzipped, remove the side window retainers
from the door channel and body side channel. Repeat
this step on the opposite side.
12. Finish releasing the sail panel retainers from the body
side channel at the rear corners of the vehicle.
NOTE:
When releasing the sail panel retainers, it is helpful
to pull down on the rear roof bow.
13. Fold the sail panels so that they rest on top of the soft
top.
Step Twelve
Step Thirteen
146
GETTING TO KNOW YOUR VEHICLE
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст