Jeep Wrangler JK (2018 year). Instruction — part 10
14. The swing gate brackets do not need to be removed
unless the hard top is being installed. To remove the
swing gate brackets, pull the front of the bracket
forward while rolling the entire bracket back in toward
the vehicle to disengage.
15. Grasp the front side bow behind the header, and lift the
top.
Step Fourteen
Step Fifteen
3
GETTING TO KNOW YOUR VEHICLE
147
16. Fold back the front section of the top, pulling the fabric
rearward. Gently rest the header on top of the rear
portion of the deck.
17. Fold the top so that the material forms a
⬙W⬙ as shown.
Enter the vehicle and move the material into two folds.
Step Sixteen
Step Seventeen
148
GETTING TO KNOW YOUR VEHICLE
18. Release the side bows by pushing down on the latch
above the front of the rear door. Push the top rearward
to disengage. Repeat this step on the other side.
19. Before lowering the top, open the swing gate to prevent
possible damage to the rear center high-mounted brake
light. Grasp the folded side bows and slide the top
along the door frame track to the rear door frame.
Step Eighteen
Step Nineteen
3
GETTING TO KNOW YOUR VEHICLE
149
20. Gently slide the side bows off the door frame track and
lower the top down into the vehicle.
NOTE:
Help from another person will ease this operation.
21. Tuck the fabric and the check straps between the bows
as far inside as possible. This will keep any portion of
the top from flapping outside of the vehicle.
22. Once the top is fully down, use the Velcro straps
provided to secure the top to the vehicle by wrapping
the strap around the side bows and through the slot on
the body.
23. Close the front header latches.
24. Remove the door frames, if desired. Refer to “Door
Frame” in this section for further information.
Step Twenty
Step Twenty-Two
150
GETTING TO KNOW YOUR VEHICLE
Putting Up The Soft Top
NOTE:
Be extremely careful when putting up the soft top
to prevent the doors from getting scratched. It may be
helpful to open the rear doors.
1. Install the door frames, if removed. Refer to “Door
Frame” in this section for further information.
2. Undo the straps used to secure the top in the down
position and store in secure location.
3. Open the swing gate.
4. Grasp the folded side bows and lift to the top of the rear
door frames.
NOTE:
Help from another person will ease this operation.
Step Four
3
GETTING TO KNOW YOUR VEHICLE
151
5. Insert the slider feature of the knuckles into the door
frame tracks and slide the top forward.
6. Ensure that the top locks into the Sunrider locking
mechanisms that are located above the front of the rear
doors.
Step Five
Step Six
152
GETTING TO KNOW YOUR VEHICLE
7. Unclip and move the sun visors to the side.
8. Standing on the side of the vehicle, lift the top by the
side bow until it rests on the windshield frame.
9. Open the header latches and engage the hook on each
side onto the windshield loops (do not close the latches).
Step Eight
Step Nine
3
GETTING TO KNOW YOUR VEHICLE
153
10. If the swing gate brackets were removed, install them
by hooking the rear edge of the bracket on the interior
side of the body channel. Then, rotate it rearward and
over the channel until it snaps onto the exterior part of
the rail. To be properly located, the bracket must only
be clipped to the shortened rail edge.
11. Ensure that the straps are positioned correctly before
pulling the sail panels over the rear roof bow (4–bow).
Step Ten
Step Eleven
154
GETTING TO KNOW YOUR VEHICLE
Partially install the sail panel retainers into the body side
channel, leaving the last 3 inches (7.6 cm) toward the rear
window loose (on both sides). Pulling down on the rear
roof bow (4–bow) will aid in reaching the channel with the
retainers.
12. To install the side windows, affix the window tempo-
rarily by attaching it to the Velcro in the upper rear
corner. Start the zipper but close only about 1 inch (2.5
cm).
Step Eleven
Step Twelve
3
GETTING TO KNOW YOUR VEHICLE
155
13. Insert the front retainer of the window into the door
channel, making sure the retainer is fully seated and
properly positioned on the door frame. Failure to do so
can result in wind and water leaks or damage to the
window.
Step Thirteen
Retainer Insertion
1 — Incorrect Insertion
2 — Correct Insertion
156
GETTING TO KNOW YOUR VEHICLE
14. Insert the retainer along the bottom edge of the win-
dow into the bottom side channel, beginning at the
front and working to the rear of the vehicle. Finish by
closing the zipper completely and attaching the Velcro
along the top and rear of the window. Repeat this step
for the opposite side.
Step Fourteen
Step Fourteen
3
GETTING TO KNOW YOUR VEHICLE
157
15. Locate the black swing gate bar. Slide the swing gate
bar over the receiver at the bottom inside of the rear
window. The spongy part of the seal should be down
and pointed outward to seal with the swing gate when
closed.
16. Install the rear window by starting both zipper ends at
the lower left corner of the rear window opening.
Ensure that the zippers are properly started and
aligned before zipping to prevent damage.
Step Fifteen
Step Sixteen
158
GETTING TO KNOW YOUR VEHICLE
17. Run the first zipper fully around to the right side of the
window.
18. Grasp the swing gate bar and position it into the swing
gate brackets.
19. Insert the rear window retainer into the swing gate
bracket on both the left and right sides.
Step Eighteen
Step Nineteen
3
GETTING TO KNOW YOUR VEHICLE
159
20. Complete the installation of the sail panel by inserting
the rest of the retainer into the body channel.
21. Close the header latches and return the sun visors to
their secured position.
SUNRIDER (FOUR-DOOR MODELS) — IF
EQUIPPED
CAUTION!
Operating the top, opening a door or lowering a
window while the top is wet may allow water to drip
into the vehicle’s interior.
NOTE:
If you are going to be driving faster than 40 mph
(64 km/h) with the Sunrider feature open, it is recom-
mended that you remove the rear window of the vehicle.
Step Twenty-One
160
GETTING TO KNOW YOUR VEHICLE
Opening The Sunrider
1. Unclip and move the sun visors to the side.
2. Release the header latches from the loops on the wind-
shield frame.
3. Grasp the front side bow behind the header, and lift the
top.
Step Two
Step Three
3
GETTING TO KNOW YOUR VEHICLE
161
4. Fold back the front section of the top and gently rest the
header on top of the rear portion of the deck.
5. Fold the top so that the material forms a
⬙W⬙ as shown.
Enter the vehicle and move the material into two folds.
Step Four
Step Five
162
GETTING TO KNOW YOUR VEHICLE
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст