Jeep Grand Cherokee WK. Manual — part 1288
SPECIFICATIONS
TORQUE CHART
TORQUE SPECIFICATIONS
DESCRIPTION
N·m
Ft. Lbs.
In. Lbs.
Rack and Pinion Steering
Gear
Gear to Frame Bolts
217
160
—
Rack and Pinion Steering
Gear
Intermediate Shaft Bolt
49
36
—
Tie Rod End
Knuckle Nut
95
70
—
Tie Rod End
Jam Nut
81
60
—
Power Steering Lines
ALL
28
21
275
19 - 66
GEAR - SERVICE INFORMATION
WK
LINKAGE - SERVICE INFORMATION
TABLE OF CONTENTS
page
page
TIE ROD END
. . . . . . . . . . . . . . . . . . . 67
INSTALLATION - OUTER TIE ROD END
TIE ROD END
STANDARD PROCEDURE
STEERING LINKAGE
The tie rod end and ball stud seals should be inspected during all oil changes. If a seal is damaged, replace the tie
rod.
CAUTION: If any steering components are replaced or serviced an alignment must be performed, to ensure
the vehicle meets all alignment specifications.
REMOVAL - OUTER TIE ROD END
NOTE: Do not twist the boot anytime during
removal or installation.
1. Loosen the jam nut (3).
2. Remove the outer tie rod end (2) nut (1) from the
ball stud.
WK
LINKAGE - SERVICE INFORMATION
19 - 67
3. Separate the outer tie rod end (3) from the knuckle
with Remover 8677 (5).
4. Unthread the outer tie rod end (3) from the inner tie
rod (1). Count the number of turns when remov-
ing the tie rod end, This will give a good start-
ing
point
when
reassembiling
and
toe
adjustment.
INSTALLATION - OUTER TIE ROD END
NOTE: Do not twist the boot at anytime during
removal or installation.
NOTE: Make sure jam nut (3) is installed on inner
tie rod end (4) before the outer tie rod end (2) is
installed.
1. Thread the outer tie rod end (2) onto the inner tie
rod (4), to it’s original position.
2. Install the outer tie rod end into the steering
knuckle (5) Tighten to 95 N·m (70 ft.lbs.).
3. Set wheel toe pattern, (Refer to 2 - SUSPENSION/
WHEEL
ALIGNMENT
-
STANDARD
PROCE-
DURE).
4. Tighten jam nut (3) to 81N·m (60 ft. lbs.).
19 - 68
LINKAGE - SERVICE INFORMATION
WK
PUMP - SERVICE INFORMATION
TABLE OF CONTENTS
page
page
PUMP - SERVICE INFORMATION
. . . . . . . . . . . . . . . . . . . . . . . . . 70
. . . . . . . . . . . . . . . . . . . . . . . . . . . 70
. . . . . . . . . . . . . . . . . . . 70
INITIAL OPERATION - WITH HYDRAULIC
COOLING FAN . . . . . . . . . . . . . . . . . . . . . . . . 71
. . . . . . . . . . . . . . . . . . . . 72
. . . . . . . . . . . . . . . . . . . . . . . . . 72
. . . . . . . . . . . . . . . . . . . . 73
. . . . . . . . . . . . . . . . . . . . . . . . . 73
. . . . . . . . . . . . . . . . . . . . . . 74
FLUID
CHECKING . . . . . . . . . . . . . . . . . . . . . . . . . . 74
FLUID COOLER
HOSES - 3.7L & 4.7L
. . . . . . . . . . . . . . . . . . . . . . 81
. . . . . . . . . . . . . . . . . . . . . . . . 81
HOSES - 5.7L
. . . . . . . . . . . . . . . . . . . . . . 84
. . . . . . . . . . . . . . . . . . . . . . . . 85
SUPPLY HOSE - PUMP TO RESERVOIR
. . . . . . . . . . . . . . . . . . . . . . . . . . . 87
SUPPLY HOSE - PUMP TO RESERVOIR
. . . . . . . . . . . . . . . . . . . . . . . 94
PULLEY
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 98
. . . . . . . . . . . . . . . . . . . . . . . . . 98
RESERVOIR
FUILD RESERVOIR - 5.7L & DIESEL
FLUID RESERVOIR - 5.7L & DIESEL
WK
PUMP - SERVICE INFORMATION
19 - 69
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст