Jeep Grand Cherokee WK. Manual — part 1589
SPECIAL TOOLS
BODY
Trim Stick C-4755
TORX BIT SET C-4794-B
REMOVER, MOLDINGS C-4829-A
Outer Belt Molding Remover - 9093
23 - 14
BODY
WK
DOOR - FRONT
TABLE OF CONTENTS
page
page
CHANNEL-GLASS
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
. . . . . . . . . . . . . . . . . . . . . . . . . 16
CYLINDER-LOCK
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
. . . . . . . . . . . . . . . . . . . . . . . . . 16
DOOR
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
. . . . . . . . . . . . . . . . . . . . . . . . . 18
. . . . . . . . . . . . . . . . . . . . . . . . 18
GLASS
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
. . . . . . . . . . . . . . . . . . . . . . . . . 22
HANDLE-EXTERIOR
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
. . . . . . . . . . . . . . . . . . . . . . . . . 24
HINGE
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
. . . . . . . . . . . . . . . . . . . . . . . . . 26
LATCH
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
. . . . . . . . . . . . . . . . . . . . . . . . . 28
. . . . . . . . . . . . . . . . . . . . . . . . 29
PANEL-TRIM
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
. . . . . . . . . . . . . . . . . . . . . . . . . 30
REGULATOR-WINDOW
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
. . . . . . . . . . . . . . . . . . . . . . . . . 32
STRIKER
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
. . . . . . . . . . . . . . . . . . . . . . . . . 33
. . . . . . . . . . . . . . . . . . . . . . . . 33
WATERSHIELD
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
. . . . . . . . . . . . . . . . . . . . . . . . . 34
CHANNEL-GLASS
REMOVAL
1. Remove the outside rearview mirror (Refer to 23 -
BODY/EXTERIOR/OUTSIDE REARVIEW MIRROR
- REMOVAL).
2. Remove the front door glass (Refer to 23 - BODY/
DOOR - FRONT/DOOR GLASS - REMOVAL).
3. Remove the weatherstrip from the front glass run
channel.
4. Remove the nut (2) that secures the top of the
front glass run channel (1) to the inside door panel.
5. Loosen the nut (3) that secures the bottom of the
run channel to the keyed hole on the inside door
panel.
6. Lift the front glass run channel upward within the
door far enough to disengage the nut that secures
the bottom of the run channel to the keyed hole on
the inside door panel.
7. Remove the front glass run channel from the door.
WK
DOOR - FRONT
23 - 15
INSTALLATION
1. Position the front glass run channel (1) onto the
door.
2. Engage the nut (3) into the keyed hole on the
inside door panel.
3. Install the nut (2) that secures the top of the front
glass run channel to the inside door panel. Tighten
the nut to 10 N·m (89 in. lbs.).
4. Tighten the nut that secures the bottom of the front
glass run channel to the inside door panel to 10
N·m (89 in. lbs.).
5. Install the weatherstrip onto the front glass run
channel.
6. Install the front door glass (Refer to 23 - BODY/
DOOR - FRONT/DOOR GLASS - INSTALLATION).
7. Install the outside rearview mirror (Refer to 23 -
BODY/EXTERIOR/OUTSIDE REARVIEW MIRROR
- INSTALLATION).
CYLINDER-LOCK
REMOVAL
NOTE: A door lock cylinder is used only on the driver side front door exterior handle.
1. Remove the exterior door handle (1) from the out-
side of the driver side front door (Refer to 23 -
BODY/DOOR - FRONT/EXTERIOR HANDLE -
REMOVAL).
2. Using hand pressure, push on the face of the lock
cylinder (2) until it pops out of the cavity in the
back of the door handle.
INSTALLATION
NOTE: A door lock cylinder is used only on the driver side front door exterior handle.
23 - 16
DOOR - FRONT
WK
1. Insert the lock cylinder (2) into the cavity on the
back of the driver side exterior door handle (1).
2. Align the lock cylinder in the handle by aligning the
two screw holes on the lock cylinder housing with
the mounting holes of the door handle.
3. Install the exterior door handle onto the outside of
the driver side front door (Refer to 23 - BODY/
DOOR
-
FRONT/EXTERIOR
HANDLE
-
INSTALLATION).
DOOR
REMOVAL
1. Disconnect and isolate the negative battery cable.
2. Disconnect the front door wire harness connector
from the body wire harness.
3. Using a grease pencil or equivalent, mark the loca-
tion of the front door hinges (1 and 2) on the A-pil-
lar.
4. Support the front door with a suitable lifting device
and remove the four bolts (3) that secure the front
door hinges to the A-pillar.
5. Carefully remove the door from the body.
6. If required, remove the front door hinges from the
door (Refer to 23 - BODY/DOOR - FRONT/HINGE
- REMOVAL).
WK
DOOR - FRONT
23 - 17
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст