Jeep Grand Cherokee WK. Manual — part 697
B2317-WIPER HI/LOW CONTROL CIRCUIT LOW
For the Wiper/Washer system circuit diagram (Refer to 8 - ELECTRICAL/WIPERS/WASHERS - SCHEMATICS AND
DIAGRAMS).
For a complete wiring diagram Refer to Section 8W.
•
When Monitored:
•
With the ignition on.
•
Set Condition:
•
When the FCM detects a short/low condition.
Possible Causes
INTEGRATED POWER MODULE
Diagnostic Test
1.
INTEGRATED POWER MODULE
Turn the ignition off.
Replace the Wiper HI/LOW relay with and known good relay.
With the Scan Tool, clear all FCM DTC’s.
Turn the Wipers ON then OFF.
With the Scan Tool, read the Wiper DTC’s.
Does the Scan Tool read: B2317-WIPER HI/LOW CONTROL CIRCUIT LOW?
Yes
>> Replace the Integrated Power Module in accordance with the service information.
Perform the BODY VERIFICATION TEST — VER 1. (Refer to 8 - ELECTRICAL/ELECTRONIC CON-
TROL MODULES - STANDARD PROCEDURE)
No
>> Test complete.
Perform the BODY VERIFICATION TEST — VER 1. (Refer to 8 - ELECTRICAL/ELECTRONIC CON-
TROL MODULES - STANDARD PROCEDURE)
8R - 10
WIPERS/WASHERS - ELECTRICAL DIAGNOSTICS
WK
B2318-WIPER HI/LOW CONTROL CIRCUIT HIGH
For the Wiper/Washer system circuit diagram (Refer to 8 - ELECTRICAL/WIPERS/WASHERS - SCHEMATICS AND
DIAGRAMS).
For a complete wiring diagram Refer to Section 8W.
•
When Monitored:
•
With the ignition on.
•
Set Condition:
•
When the FCM detects a short/HIGH condition.
Possible Causes
INTEGRATED POWER MODULE
Diagnostic Test
1.
INTEGRATED POWER MODULE
Turn the ignition off.
Replace the Wiper HI/LOW relay with and known good relay.
With the Scan Tool, clear all FCM DTC’s.
Turn the Wipers ON then OFF.
With the Scan Tool, read the Wiper DTC’s.
Does the Scan Tool read: B2318-WIPER HI/LOW CONTROL CIRCUIT HIGH?
Yes
>> Replace the Integrated Power Module in accordance with the service information.
Perform the BODY VERIFICATION TEST — VER 1. (Refer to 8 - ELECTRICAL/ELECTRONIC CON-
TROL MODULES - STANDARD PROCEDURE)
No
>> Test complete.
Perform the BODY VERIFICATION TEST — VER 1. (Refer to 8 - ELECTRICAL/ELECTRONIC CON-
TROL MODULES - STANDARD PROCEDURE)
WK
WIPERS/WASHERS - ELECTRICAL DIAGNOSTICS
8R - 11
B2319-WIPER HI/LOW CONTROL CIRCUIT OPEN
For the Wiper/Washer system circuit diagram (Refer to 8 - ELECTRICAL/WIPERS/WASHERS - SCHEMATICS AND
DIAGRAMS).
For a complete wiring diagram Refer to Section 8W.
•
When Monitored:
•
With the ignition on.
•
Set Condition:
•
When the FCM detects a short/low condition.
Possible Causes
INTEGRATED POWER MODULE
Diagnostic Test
1.
INTEGRATED POWER MODULE
Turn the ignition off.
Replace the Wiper HI/LOW relay with and known good relay.
With the Scan Tool, clear all FCM DTC’s.
Turn the Wipers ON then OFF.
With the Scan Tool, read the Wiper DTC’s.
Does the Scan Tool read: B2319-WIPER HI/LOW CONTROL CIRCUIT OPEN?
Yes
>> Replace the Integrated Power Module in accordance with the service information.
Perform the BODY VERIFICATION TEST — VER 1. (Refer to 8 - ELECTRICAL/ELECTRONIC CON-
TROL MODULES - STANDARD PROCEDURE)
No
>> Test complete.
Perform the BODY VERIFICATION TEST — VER 1. (Refer to 8 - ELECTRICAL/ELECTRONIC CON-
TROL MODULES - STANDARD PROCEDURE)
8R - 12
WIPERS/WASHERS - ELECTRICAL DIAGNOSTICS
WK
B231F-FRONT/REAR WASHER MOTOR CONTROL CIRCUIT LOW
WK
WIPERS/WASHERS - ELECTRICAL DIAGNOSTICS
8R - 13
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст