Jeep Grand Cherokee WK. Manual — part 698
B231F-FRONT/REAR WASHER MOTOR CONTROL CIRCUIT LOW (CONTINUED)
For the Wiper/Washer system circuit diagram (Refer to 8 - ELECTRICAL/WIPERS/WASHERS - SCHEMATICS AND
DIAGRAMS).
For a complete wiring diagram Refer to Section 8W.
•
When Monitored:
•
With the ignition on.
•
Set Condition:
•
When the FCM detects a short/low condition on the washer Pump Motor Control circuit.
Possible Causes
(W10)/(W20) WASHER PUMP MOTOR CONTROL CIRCUIT SHORT TOGETHER
(W10) WASHER PUMP MOTOR CONTROL CIRCUIT SHORT TO GROUND
(W20) WASHER PUMP MOTOR CONTROL CIRCUIT SHORT TO GROUND
WIPER WASHER PUMP
FRONT CONTROL MODULE
Diagnostic Test
1.
INTERMITTENT CONDITION
Turn the ignition on.
With the Scan Tool, clear all FCM DTC’s.
Turn the Washers on.
With the Scan Tool, read the Wiper/Washers DTC’s.
Does the Scan Tool read: B231F-FRONT/REAR WASHER MOTOR CONTROL CIRCUIT LOW?
Yes
>> Go To 2
No
>> The condition that caused the symptom is currently not present. Inspect the related wiring for a possible
intermittent condition. Look for any chafed, pierced, pinched, or partially broken wires.
Perform the BODY VERIFICATION TEST — VER 1. (Refer to 8 - ELECTRICAL/ELECTRONIC CON-
TROL MODULES - STANDARD PROCEDURE)
2.
WASHER PUMP MOTOR
Turn the ignition off.
Disconnect the Washer Pump Motor connector.
Turn the ignition on.
With the Scan Tool, read the DTC’s.
Does the Scan Tool read:B231F-FRONT/REAR WASHER MOTOR
CONTROL CIRCUIT LOW?
Yes
>> Go To 3
No
>> Replace the Washer Pump Motor in accordance with the
service information.
Perform the BODY VERIFICATION TEST — VER 1.
(Refer to 8 - ELECTRICAL/ELECTRONIC CONTROL
MODULES - STANDARD PROCEDURE)
8R - 14
WIPERS/WASHERS - ELECTRICAL DIAGNOSTICS
WK
B231F-FRONT/REAR WASHER MOTOR CONTROL CIRCUIT LOW (CONTINUED)
3.
(W10)/(W20) WASHER PUMP MOTOR CONTROL CIRCUITS SHORT TOGETHER
Turn the ignition off.
Disconnect the Washer Pump Motor harness connector.
Disconnect the IPM C1 harness connector.
Measure the resistance between the (W10) and (W20) Washer Pump
Motor Control circuits.
Is the resistance below 5.0 ohms?
Yes
>> Repair the (W10) and (W20) Washer Pump Motor Control
circuits for a short together.
Perform the BODY VERIFICATION TEST — VER 1.
(Refer to 8 - ELECTRICAL/ELECTRONIC CONTROL
MODULES - STANDARD PROCEDURE)
No
>> Go To 4
4.
(W10) WASHER PUMP MOTOR CONTROL CIRCUIT SHORT
TO GROUND
Measure the resistance between ground and the (W10) Washer Pump
Motor Control circuit.
Is the resistance below 5.0 ohms?
Yes
>> Repair the (W10) Washer Pump Motor Control circuit for a
short to ground.
Perform the BODY VERIFICATION TEST — VER 1.
(Refer to 8 - ELECTRICAL/ELECTRONIC CONTROL
MODULES - STANDARD PROCEDURE)
No
>> Go To 5
WK
WIPERS/WASHERS - ELECTRICAL DIAGNOSTICS
8R - 15
B231F-FRONT/REAR WASHER MOTOR CONTROL CIRCUIT LOW (CONTINUED)
5.
(W20) WASHER PUMP MOTOR CONTROL CIRCUIT SHORT TO GROUND
Measure the resistance between ground and the (W20) Washer Pump
Motor Control circuit.
Is the resistance below 5.0 ohms?
Yes
>> Repair the (W20) Washer Pump Motor Control circuit for a
short to ground.
Perform the BODY VERIFICATION TEST — VER 1.
(Refer to 8 - ELECTRICAL/ELECTRONIC CONTROL
MODULES - STANDARD PROCEDURE)
No
>> Replace the Front Control Module in accordance with the
service information.
Perform the BODY VERIFICATION TEST — VER 1.
(Refer to 8 - ELECTRICAL/ELECTRONIC CONTROL
MODULES - STANDARD PROCEDURE)
8R - 16
WIPERS/WASHERS - ELECTRICAL DIAGNOSTICS
WK
B2320-FRONT/REAR WASHER MOTOR CONTROL CIRCUIT HIGH
WK
WIPERS/WASHERS - ELECTRICAL DIAGNOSTICS
8R - 17
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст