Jeep Grand Cherokee WK. Manual — part 1602
RACK-LUGGAGE
REMOVAL
1. Remove luggage rack end covers, pull straight up.
2. Remove the mounting bolts.
3. Remove luggage rack bars.
INSTALLATION
1. Locate luggage rack bar.
2. Install mounting bolts.
3. Tighten mounting bolts.
4. Install luggage rack bar covers.
23 - 66
EXTERIOR
WK
HOOD
TABLE OF CONTENTS
page
page
HINGE
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67
. . . . . . . . . . . . . . . . . . . . . . . . . 68
HOOD
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69
. . . . . . . . . . . . . . . . . . . . . . . . . 69
LATCH
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70
. . . . . . . . . . . . . . . . . . . . . . . . . 71
RELEASE-HOOD LATCH
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72
. . . . . . . . . . . . . . . . . . . . . . . . . 72
CYLINDER-HOOD SUPPORT
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73
. . . . . . . . . . . . . . . . . . . . . . . . . 74
HINGE
REMOVAL
NOTE: It is not necessary to remove the hood to
replace the hood hinges. Hood hinges can be
replaced one at a time.
1. Using a grease pencil or equivalent, mark the posi-
tion of the hood hinge on the hood for the hinge
being serviced.
2. Support the hood and disconnect the support cylin-
der (2) from the hood (Refer to 23 - BODY/HOOD/
SUPPORT CYLINDER - REMOVAL).
3. Remove the bolts (3) that secureto the hood hinge
(1) to the hood (2)..
4. Remove the bolt that secures the hood hinge (1) to
the front fender.
WK
HOOD
23 - 67
INSTALLATION
NOTE: It is not necessary to remove the hood to
replace the hood hinges. Hood hinges can be
replaced one at a time.
1. Position the hood hinge (1) onto the hood (2).
2. Align the hood to the hood hinge using the refer-
ence marks made during the removal procedure
and Install the bolts (3) that secure the hood hinge
to the hood (2). Tighten the bolts to 20 N·m (15 ft.
lbs.).
3. Install the bolts (2) that secures the hood hinge (1)
to the fender rail. Tighten the bolt to 17 N·m (13 ft.
lbs.).
4. Align the hood to the hood hinge using the refer-
ence marks made during the removal procedure
and tighten the nuts to 23 N·m (17 ft. lbs.).
5. Install the support cylinder (4) (Refer to 23 - BODY/
HOOD/SUPPORT CYLINDER - INSTALLATION).
6. If required, adjust the hood to the correct position
(Refer to 23 - BODY/BODY STRUCTURE/GAP
AND FLUSH - SPECIFICATIONS).
23 - 68
HOOD
WK
HOOD
REMOVAL
1. Disconnect and isolate the negative battery cable.
2. Remove the underhood lamp unit from the hood (1)
(Refer to 8 - ELECTRICAL/LAMPS/LIGHTING -
EXTERIOR/UNDERHOOD
LAMP
UNIT
-
REMOVAL).
3. Using a grease pencil or equivalent, mark the posi-
tion of the hood hinges (1) on the hood.
4. Support the hood and disconnect the support cylin-
ders (4) from the hood (Refer to 23 - BODY/
HOOD/SUPPORT CYLINDER - REMOVAL).
5. Remove the two bolts that secure the hood to each
hood hinge and remove the hood.
INSTALLATION
1. Position the hood onto the hood hinges (2) and
loosely install the two nuts that secure the hood to
each hood hinge (1).
2. Align the hood to the hood hinges (1) using the ref-
erence marks made during the Removal procedure
and tighten the nuts to 23 N·m (17 ft. lbs.).
3. Install the support cylinders (4) to the hood (Refer
to 23 - BODY/HOOD/SUPPORT CYLINDER -
INSTALLATION).
4. Install the underhood lamp unit (Refer to 8 - ELEC-
TRICAL/LAMPS/LIGHTING - EXTERIOR/UNDER-
HOOD LAMP UNIT - INSTALLATION.
5. Reconnect the negative battery cable.
6. If required, adjust the hood to the correct position
(Refer to 23 - BODY/BODY STRUCTURE/GAP
AND FLUSH - SPECIFICATIONS).
WK
HOOD
23 - 69
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст