Jeep Grand Cherokee WK. Manual — part 1599
EXTERIOR
TABLE OF CONTENTS
page
page
BODY SIDE MOLDINGS
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
. . . . . . . . . . . . . . . . . . . . . . . . . 54
CROSSMEMBER-RADIATOR
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
. . . . . . . . . . . . . . . . . . . . . . . . . 55
FENDER
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56
. . . . . . . . . . . . . . . . . . . . . . . . . 59
GRILLE
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61
. . . . . . . . . . . . . . . . . . . . . . . . . 62
LINER-FENDER & QUARTER PANEL
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62
. . . . . . . . . . . . . . . . . . . . . . . . . 63
MIRROR-OUTSIDE REARVIEW
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63
. . . . . . . . . . . . . . . . . . . . . . . . . 64
PANEL-COWL TOP
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64
. . . . . . . . . . . . . . . . . . . . . . . . . 65
RACK-LUGGAGE
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66
. . . . . . . . . . . . . . . . . . . . . . . . . 66
BODY SIDE MOLDINGS
REMOVAL
1. Apply a length of masking tape on the body, parallel to the top edge of the molding to use as a guide, if nec-
essary.
2. Warm the effected adhesive type molding and body metal to approximately 38°C (100°F) using a suitable heat
lamp or heat gun.
3. Pull stick-on molding from painted surface.
INSTALLATION
1. Clean body surface with MOPAR
T
Super Kleen solvent or equivalent. Wipe surface dry with lint free cloth.
2. Remove protective cover from tape on back of molding. Apply molding to body below the masking tape guide.
3. Remove masking tape guide and firmly press molding to body surface to assure adhesion.
23 - 54
EXTERIOR
WK
CROSSMEMBER-RADIATOR
REMOVAL
1. Remove the grill assembly, (Refer to 23 - BODY/
EXTERIOR/GRILLE - REMOVAL).
2. Remove the front hood seal.
3. Remove the center brace mounting nuts and
remove hood latch.
4. Remove the outer crossmember mounting bolts.
5. Remove crossmember.
INSTALLATION
1. Install upper crossmember.
2. Install outer mounting bolts and tighten.
3. Install nuts attaching latch to radiator crossmember
support. Tighten nuts to 11 N·m (8 ft. lbs.) torque.
4. Install grill assembly, (Refer to 23 - BODY/EXTERI-
OR/GRILLE - INSTALLATION).
5.
6. Check hood fit and adjust if required. (Refer to 23 -
BODY/BODY STRUCTURE/GAP AND FLUSH -
SPECIFICATIONS)
7. Install hood seal.
WK
EXTERIOR
23 - 55
FENDER
REMOVAL
1. Mark fender location.
2. Remove wheel if necessary.
3. Remove wheel liner, (Refer to 23 - BODY/EXTERIOR/LF WHEELHOUSE SPLASH SHIELD - REMOVAL).
4. Remove front fascia as necessary, (Refer to 13 - FRAME & BUMPERS/BUMPERS/FRONT FASCIA -
REMOVAL).
23 - 56
EXTERIOR
WK
5. Remove front lower mounting bolts.
6. Loosen rocker panel cover as necessary.
7. Remove rear lower mounting bolts.
WK
EXTERIOR
23 - 57
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст