Jeep Grand Cherokee WK. Manual — part 1598
REGULATOR-WINDOW
REMOVAL
1. Remove the trim panel from the inside of the rear
door (Refer to 23 - BODY/DOORS - REAR/TRIM
PANEL - REMOVAL).
2. Position the watershield out of the way and using
the regulator, move the rear door glass up or down
as required to access the two window regulator
glass clamp bolts (Refer to 23 - BODY/DOORS -
REAR/DOOR GLASS - REMOVAL).
3. Loosen the bolt in each of the window regulator
glass clamps far enough to release the door glass
from the clamps.
4. Disengage the door glass from the window regula-
tor glass clamps and lift the glass out of the regu-
lator clamps and into its full up position, then tape
the glass securely into place.
5. Remove the bolt (4) that secures the bottom of the
window regulator to the inside of the door.
6. Loosen the two bolts (1) that secure the regulator
to the keyed holes (2) on the inside of the door.
7. Lift the regulator upward within the door far enough to disengage the bolts from the two keyed holes in the door.
8. Lower the regulator within the door far enough to access and disconnect the wire harness connector (3) from the
regulator motor through the large access hole in the door and remove the regulator.
INSTALLATION
1. Load the window regulator into the rear door
through the large access hole in the door and con-
nect the wire harness connector (3) to the regulator
motor.
2. Engage the two bolts (1) into the keyed holes (2)
on the inside of the door.
3. Install the bolt (4) that secures the bottom of the
regulator to the door. Tighten the bolt to 10 N·m
(90 in. lbs.).
4. Tighten the bolts that secure the regulator to the
two keyed holes on the inside of the door. Tighten
the bolts to 10 N·m (90 in. lbs.).
5. Carefully remove the tape securing the rear door
glass in its full up position, then lower the glass
and engage it into the two window regulator glass
clamps (Refer to 23 - BODY/DOORS - REAR/
DOOR GLASS - INSTALLATION).
6. Using the regulator, move the rear door glass up or
down as required to access to the two window reg-
ulator glass clamp bolts.
7. Tighten the bolts in each of the window regulator glass clamps to 10 N·m (90 in. lbs.).
8. Install the watershield and the trim panel onto the inside of the rear door (Refer to 23 - BODY/DOORS - REAR/
TRIM PANEL - INSTALLATION).
23 - 50
DOORS - REAR
WK
STRIKER
REMOVAL
1. Using a grease pencil or equivalent, mark the loca-
tion of the door latch striker (2) on the C-pillar.
2. Remove the two bolts (1) that secure the striker
and the shim (3) to the C-pillar and remove the
striker and shim.
INSTALLATION
1. Position the door latch striker (2) and the shim (3)
onto the C-pillar and loosely install the two bolts
(1).
2. Align the door latch striker to the C-pillar using the
reference marks made during the removal proce-
dure and tighten the bolts to 28 N·m (21 ft. lbs.).
3. If necessary, adjust the rear door latch striker
(Refer to 23 - BODY/DOORS - REAR/LATCH
STRIKER - ADJUSTMENTS).
WK
DOORS - REAR
23 - 51
ADJUSTMENTS
ADJUSTMENT
1. Using a grease pencil or equivalent, mark the loca-
tion of the door latch striker (2) and shim (3) on the
C-pillar to aid in adjustment.
2. Loosen the two bolts (1) that secure the door latch
striker to the C-pillar.
3. To adjust the rear gap and flush measurement,
change the position of the door latch striker and
then tighten the two bolts to 28 N·m (21 ft. lbs.)
(Refer to 23 - BODY/BODY STRUCTURE/GAP
AND FLUSH - SPECIFICATIONS).
4. Verify correct door and latch position.
WATERSHIELD
REMOVAL
1. Remove the trim panel from the inside of the rear
door (Refer to 23 - BODY/DOORS - REAR/TRIM
PANEL - REMOVAL).
2. If equipped, remove the speaker from the inside of
the rear door (Refer to 8 - ELECTRICAL/AUDIO/
SPEAKER - REMOVAL).
CAUTION: Do not allow the watershield adhesive
to become contaminated with dirt or other foreign
substances. If the watershield becomes contami-
nated or damaged, replace it.
3. Carefully remove the watershield (1) from around
the perimeter of the door (2).
4. Separate the watershield from the interior handle
actuator rod and the door wire harness and remove
the watershield.
23 - 52
DOORS - REAR
WK
INSTALLATION
CAUTION: Do not allow the watershield or adhe-
sive to become contaminated with dirt or other
foreign substances. If the watershield becomes
contaminated or damaged, replace it.
NOTE: Be sure that the watershield is fully sealed
around the perimeter of the door.
1. Position the interior handle actuator rod and the
wire harness through the holes in the watershield
(1) and install the watershield to the door (2).
2. If equipped, install the speaker onto the inside of
the rear door (Refer to 8 - ELECTRICAL/AUDIO/
SPEAKER - INSTALLATION)
3. Install the trim panel onto the inside of the rear
door (Refer to 23 - BODY/DOORS - REAR/TRIM
PANEL - INSTALLATION).
WK
DOORS - REAR
23 - 53
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст