Jeep Grand Cherokee WK. Manual — part 1618
LIFTGATE
TABLE OF CONTENTS
page
page
GLASS
. . . . . . . . . . . . . . . . . . . . . . . . . . . . 130
. . . . . . . . . . . . . . . . . . . . . . . . 132
. . . . . . . . . . . . . . . . . . . . . . . 133
HANDLE
. . . . . . . . . . . . . . . . . . . . . . . . . . . . 133
. . . . . . . . . . . . . . . . . . . . . . . . 134
HINGE
. . . . . . . . . . . . . . . . . . . . . . . . . . . . 135
. . . . . . . . . . . . . . . . . . . . . . . . 136
LATCH
. . . . . . . . . . . . . . . . . . . . . . . . . . . . 137
. . . . . . . . . . . . . . . . . . . . . . . . 138
LATCH-LIFTGATE GLASS
. . . . . . . . . . . . . . . . . . . . . . . . . . . . 139
. . . . . . . . . . . . . . . . . . . . . . . . 139
PANEL-TRIM
. . . . . . . . . . . . . . . . . . . . . . . . . . . . 140
. . . . . . . . . . . . . . . . . . . . . . . . 141
STRIKER-LATCH
. . . . . . . . . . . . . . . . . . . . . . . . . . . . 142
. . . . . . . . . . . . . . . . . . . . . . . . 142
SUPPORT-STRUT
. . . . . . . . . . . . . . . . . . . . . . . . . . . . 143
. . . . . . . . . . . . . . . . . . . . . . . . 143
GLASS
REMOVAL
1. Disconnect heated liftgate glass electrical connec-
tor (2).
23 - 130
LIFTGATE
WK
2. Open the liftgate and support.
3. Disconnect liftgate hydraulic cylinders (3) at the lower ball studs.
4. Close liftgate, but not latch in the closed position.
5. Remove hinge covers (1) and remove honge bolts (2).
6. Remove liftgate.
WK
LIFTGATE
23 - 131
INSTALLATION
1. Position liftgate on vehicle.
2. Install hinge bolts. Center liftgate. Tighten hinge bolts to 7 N·m (60 in. lbs.).
3. Open and support liftgate.
4. Install support cylinders (3) (Refer to 23 - BODY/DECKLID/HATCH/LIFTGATE/TAILGATE/SUPPORT CYLINDER
- INSTALLATION).
5. connect heated glass electrical connector (2).
6. Adjust liftgate as necessary (Refer to 23 - BODY/
DECKLID/HATCH/LIFTGATE/TAILGATE/FLIP-UP
GLASS - ADJUSTMENTS).
23 - 132
LIFTGATE
WK
ADJUSTMENTS
ADJUSTMENT
1. Verify that the liftgate is correctly centered in it’s
opening.
2. Confirm the liftgate adjustment. Hold a straight
edge flush against the glass as indicated, and
record the gap/space between the straight edge
and the liftgate outer vertical panel.
NOTE: The flush specification for the liftgate glass
to the outer panel is 0mm - 2mm over flush.
3. If the liftgate needs to be adjusted, loosen the two
hinge bolts and move the liftgate in small incre-
ments until desired measurement is achieved.
4. Tighten the liftgate hinge bolts 12 N·m (9 ft. lbs.).
5. Verify correct liftgate closing efforts and operation.
HANDLE
REMOVAL
1. Open the liftgate (4).
2. Disconnect and isolate the battery negative cable.
3. Remove the lower trim panel from the inside of the
liftgate. (Refer to 23 - BODY/DECKLID/HATCH/
LIFTGATE/TAILGATE/TRIM
PANEL/LOWER
-
REMOVAL).
4. Disconnect the electrical connector of the latch
handle (2) on the inside of the liftgate.
5. Reach through the clearance hole in the inside of
the liftgate panel on each side of the latch to
access and remove the two nuts (1) that secure
the handle to the liftgate.
WK
LIFTGATE
23 - 133
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст