Jeep Grand Cherokee WK. Manual — part 1616
HEADLINER
REMOVAL
1. Remove the A-pillar trim panels, (Refer to 23 - BODY/INTERIOR/A-PILLAR TRIM - REMOVAL).
2. Remove the upper B-pillar trim panels, (Refer to 23 - BODY/INTERIOR/B-PILLAR UPPER TRIM - REMOVAL).
3. Remove the upper C-pillar trim panels, (Refer to 23 - BODY/INTERIOR/C-PILLAR TRIM - REMOVAL).
4. Remove the upper liftgate trim panel, (Refer to 23 - BODY/INTERIOR/LIFTGATE OPENING UPPER TRIM -
REMOVAL).
5. Remove the D-pillar trim panels, (Refer to 23 - BODY/INTERIOR/D-PILLAR TRIM - REMOVAL).
6. Pull the top of each door seal downward slightly.
7. Fold the rear passenger seats down.
8. Disconnect the headliner wire harness connector located at the left A-pillar.
9. If equipped, disconnect the headliner wire harness connector(s) from the inside rear view mirror.
10. If equipped, disconnect the headliner wire harness connector from the rain sensor.
11. Remove the overhead console, (Refer to 8 - ELECTRICAL/OVERHEAD CONSOLE - REMOVAL).
12. Remove the sun visors, (Refer to 23 - BODY/INTERIOR/SUN VISOR - REMOVAL).
13. Remove the sun visor supports, (Refer to 23 - BODY/INTERIOR/SUN VISOR SUPPORT - REMOVAL)
14. Remove the grab handles above each rear passenger door, (Refer to 23 - BODY/INTERIOR/ASSIST HANDLE
- REMOVAL).
15. Lower the rear of the headliner downward from the roof panel and disconnect the rear washer hose.
16. Disconnect the headliner wire harness connector located at the left D-pillar.
17.
CAUTION: Be careful not to crease the headliner.Lower the front of the headliner downward and remove the
headliner through the liftgate door opening.
INSTALLATION
1.
CAUTION: Be careful not to crease the headliner.Position the headliner in the vehicle through the liftgate
door opening.
2. Connect the headliner wire harness connector located at the left D-pillar.
3. Connect the rear washer hose.
4. Raise the rear of the headliner upward.
5. Raise the front of the headliner upward and install the sun visor supports, (Refer to 23 - BODY/INTERIOR/SUN
VISOR SUPPORT - INSTALLATION).
6. Install the sun visors, (Refer to 23 - BODY/INTERIOR/SUN VISOR - INSTALLATION).
7. Install the overhead console, (Refer to 8 - ELECTRICAL/OVERHEAD CONSOLE - INSTALLATION).
8. If equipped, connect the headliner wire harness connector(s) to the inside rear view mirror.
9. If equipped, connect the headliner wire harness connector to the rain sensor.
10. Connect the headliner wire harness connector located at the left A-pillar.
11. Install the grab handle above each rear passenger door, (Refer to 23 - BODY/INTERIOR/ASSIST HANDLE -
INSTALLATION).
12. Install the A-pillar trim panels, (Refer to 23 - BODY/INTERIOR/A-PILLAR TRIM - INSTALLATION).
13. Install the upper B-pillar trim panels, (Refer to 23 - BODY/INTERIOR/B-PILLAR UPPER TRIM - INSTALLA-
TION).
14. Install the upper C-pillar trim panel, (Refer to 23 - BODY/INTERIOR/C-PILLAR TRIM - INSTALLATION).
15. Install the D-pillar trim panels, (Refer to 23 - BODY/INTERIOR/D-PILLAR TRIM - INSTALLATION).
23 - 122
INTERIOR
WK
16. Install the upper liftgate trim panel, (Refer to 23 - BODY/INTERIOR/LIFTGATE OPENING UPPER TRIM -
INSTALLATION).
17. Seat the top of each of door seal to the door opening.
18. Place the rear passenger seats in the upright position.
LIFTGATE OPENING UPPER TRIM
REMOVAL
1. Using a trim stick C-4755 or equivalent, disengage
the retaining tabs that secure the upper liftgate trim
panel to the retaining clips in the liftgate opening
and remove the trim panel.
INSTALLATION
1. Align the retaining tabs on the upper liftgate trim
panel with the retaining clips in the liftgate opening
and engage the retaining tabs that secure the trim
panel to the liftgate opening.
WK
INTERIOR
23 - 123
LIFTGATE SCUFF PLATE
REMOVAL
1. Using a trim stick C-4755 or equivalent, disengage
the retaining tabs that secure the liftgate scuff plate
to the liftgate door sill and remove the scuff plate.
INSTALLATION
1. Position the liftgate scuff plate to the liftgate door
sill and engage the retaining tabs that secure the
scuff plate to the door sill.
LOAD FLOOR
REMOVAL
1. Remove the liftgate scuff plate, (Refer to 23 - BODY/INTERIOR/LIFTGATE SCUFF PLATE - REMOVAL).
2. Remove the two nuts that secure the load floor to the floor panel.
3. Remove the load floor.
INSTALLATION
1. Position the load floor in the vehicle.
2. Install the two nuts that secure the load floor to the floor panel.
23 - 124
INTERIOR
WK
3. Install the liftgate scuff plate, (Refer to 23 - BODY/INTERIOR/LIFTGATE SCUFF PLATE - INSTALLATION).
QUARTER TRIM PANEL
REMOVAL
1. Remove the rear passenger seat cushion, (Refer to
23 - BODY/SEATS/SEAT CUSHION - REMOVAL).
2. Fold the rear passenger seat down.
3. Using a trim stick C-4755 or equivalent, disengage
the retaining tabs that secure the upper C-pillar
trim panel to the retaining clips in the C-pillar and
position the panel and the seat belt out of the way.
4. Remove the rear passenger door sill scuff plate,
(Refer
to
23
-
BODY/INTERIOR/DOOR
SILL
SCUFF PLATE - REMOVAL).
5. If equipped, remove the tonneau cover.
6. Remove the liftgate scuff plate, (Refer to 23 -
BODY/INTERIOR/LIFTGATE
SCUFF
PLATE
-
REMOVAL).
7. Remove the upper liftgate trim panel, (Refer to 23 -
BODY/INTERIOR/LIFTGATE
OPENING
UPPER
TRIM - REMOVAL).
8. Remove the D-pillar trim panel, (Refer to 23 -
BODY/INTERIOR/D-PILLAR TRIM - REMOVAL).
9. Remove the load floor, (Refer to 23 - BODY/INTERIOR/LOAD FLOOR - REMOVAL).
10. Remove the two screws that secure the quarter trim panel to the quarter panel.
11. Using a trim stick C-4755 or equivalent, disengage the retaining tabs that secure the quarter trim panel to the
quarter panel.
12. Pull the quarter trim panel away from the quarter panel.
13. If equipped, disconnect the power outlet wire harness connector.
14. Remove the quarter trim panel.
INSTALLATION
1. Position the quarter trim panel in the vehicle.
2. If equipped, connect the wire harness connector to
the power outlet.
3. Position the flange on the quarter trim panel into
the seal ditch and secure the bottom clip first and
then the middle clip.
4. Align the two fastener holes in the quarter trim
panel with the two fastener holes in the quarter
panel and engage the retaining tabs that secure
the quarter trim panel to the quarter panel.
5. Install the two screws that secure the quarter trim
panel to the quarter panel.
6. Install the load floor, (Refer to 23 - BODY/INTERI-
OR/LOAD FLOOR - INSTALLATION).
7. Install the D-pillar trim panel, (Refer to 23 - BODY/
INTERIOR/D-PILLAR TRIM - INSTALLATION).
WK
INTERIOR
23 - 125
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст