Jeep Wrangler 4xe (2023 year). Manual in english — page 5
GETTING TO KNOW YOUR VEHICLE
73
5. While keeping the rear window level, slide to the left
until it is completely separate from its retainer. Do not
pull downward while removing the rear window.
Damage to the retainer could result.
Step Five
Remove The Right And Left Quarter Windows:
1. Through the rear opening, push the bottom corner
outward and release tab from the bottom of the
window pillar.
Step One
2. Undo the hook-and-loop fastener located at the upper
front corner of each quarter window.
Step Two
3. Starting at the rear of the vehicle, remove plastic
retainer from along the bottom of the window moving
toward the front of the vehicle.
Step Three
4. Remove plastic retainer from the bottom to the top of
the front window.
Step Four
2
74
GETTING TO KNOW YOUR VEHICLE
5. While keeping the window level, slide rearward until it
is completely separate from its retainer. Do not pull
downward while removing the window. Damage to
the retainer could result.
Step Five
6. Store in soft window bag (if equipped) or a safe
location.
NOTE:
For information on the use of the storage bag, refer to the
next section.
Soft Top Window Storage Bag —
If Equipped
To safely store the soft top rear window, and rear quarter
windows, proceed as follows:
NOTE:
The swing gate bar, once removed from the rear window,
does not store in the soft window storage bag (if
equipped).
1. With the bag opened completely, fold both fabric
dividers downward and lay the first quarter window
all the way to the right side with the inside of the
window facing downward and the window pillar to
the outside.
NOTE:
The quarter windows are marked “1” and “2” on the inside
of the window pillar.
Step One
Step One
2. Fold the first divider upward, covering the first quarter
window.
Step Two
1 — Quarter Window Facing Downward
2 — Both Dividers Folded Down
GETTING TO KNOW YOUR VEHICLE
75
3. Lay the second quarter window on top of the first
divider all the way to the left side with the inside of the
window facing downward and the window pillar to the
outside.
Step Three
4. Fold the second divider upward, covering the second
quarter window.
Step Four
5. Lay the rear window on top of the second divider.
Step Five
6. Close the storage bag and store in a safe location.
Step Six
Lowering The Soft Top All The Way
1. Remove the rear window and quarter panel windows
2. From the Sunrider® position
page 67, remove
straps if previously secured and move to the rear of
the vehicle.
1 — Quarter Window Facing Downward
2 — Second Divider Folded Down
2
76
GETTING TO KNOW YOUR VEHICLE
3. Locate the Sunrider® latch beneath the #6 Bow of
the soft top on the left side.
Step Three
4. Pull the latch to release the top, and allow the soft top
to slide rearward freely in the guide tracks to the
stowed position.
Step Four
5. While pushing downward slightly on the folded soft
top, slide the lock lever on the left and right side lift
assist mechanisms to the “lock” position.
Step Five (Locked Position)
6. Once the lock lever is in the “lock” position, push
downward on each side of the folded soft top to
ensure it is secure. An audible “click” may be heard.
Step Six
NOTE:
Secure the top by using the two hook-and-loop fasteners
provided in the center console.
Step Six
CAUTION!
Failure to follow the next steps could result in damage
to the Soft Top or vehicle.
GETTING TO KNOW YOUR VEHICLE
77
R
AISING
T
HE
S
OFT
T
OP
Use this QR code to access your digital
experience.
Raising The Soft Top From The Fully
Lowered Position
1. From the fully lowered position,
remove straps if previously
secured.
2. While pushing down on the rear of the top, slide the
lock lever on the left and right side lift assist
mechanisms to the “unlock” position.
Step Two
3. Push up and forward from the #5 Bow along the guide
track until it locks into the Sunrider® position with an
audible “click”.
Step Three
4. Gently pull rearward on the #6 Bow to ensure the top
is locked in the Sunrider® position.
5. Using the side link, lift and push the soft top toward
the front of the vehicle manually guiding the top into
the closed position.
Step Five
Step Five
CAUTION!
Failure to follow the next steps could result in damage
to the Soft Top or vehicle.
1 — Unlocked Position
2 — #5 Bow Location
2
78
GETTING TO KNOW YOUR VEHICLE
6. From inside the vehicle, pull the handle on the header
latch downward to engage the hook into its receiver.
Repeat on the other side.
Step Six
7. Pull the handle back upward while squeezing the
hook, locking the latch into place.
Step Seven
Installing The Soft Top Windows
Install The Right And Left Quarter Windows
1. From the rear of the vehicle, guide the top of the
window into the retainer and slide forward while
keeping the window level. Repeat on the other side.
Step One
2. Place the top of the quarter window pillar into the top
cover, and insert the bottom tab into the clip.
Step Two
Step Two
CAUTION!
Failure to follow all Quarter Window Install steps could
result in damage to the Soft Top or vehicle.
GETTING TO KNOW YOUR VEHICLE
79
3. Engage the retainers on the front of the windows,
ensuring they are fully engaged, followed by the
retainers along the bottom of the windows.
Step Three
NOTE:
It is critical that the retainers are fully engaged before the
vehicle resumes motion.
4. Secure the hook-and-loop fastener at the upper front
corner of each quarter window by pressing firmly.
Step Four
Install The Rear Window
1. Guide the rear window into the retainer from left to
right while keeping the window level.
Step One
2. Insert the swing gate bar into the retainers at the
bottom of the window from left to the right.
Step Two
3. Rotate the swing gate bar into the left and right side
retainers.
Step Three
1 — Retainer At Front Of Quarter Window
2 — Retainer At Bottom Of Quarter Window
2
80
GETTING TO KNOW YOUR VEHICLE
4. Line up the rear window to the right side quarter
window first, and engage the plastic retainers.
5. Repeat with the left side quarter window.
Step Five
6. Engage the rear window retainers in the lower right
and left corners.
Step Six
NOTE:
For information on removing your soft top, refer to the next
section.
R
EMOVING
T
HE
S
OFT
T
OP
Use this QR code to access your digital
experience.
1. Fully lower the soft top
2. Make sure the lift assist mechanism on both the left
and right sides are in the “lock” position, and an
audible “click” is heard when pushing down on the #1
bow from each of the lift assist mechanisms before
removing.
Step Two
3. Using the provided #40 Torx head driver and ratchet,
unscrew the two Torx head screws on each lift assist
mechanism, then lift the mechanism up and away
from the vehicle.
Step Three
CAUTION!
Failure to follow the next steps could result in damage
to the Soft Top or vehicle.
1 — Lock Position
2 — Torx Head Screw
3 — Torx Head Screw
GETTING TO KNOW YOUR VEHICLE
81
4. Pull the release lever on top of the rail rearward to
release the side link from the track.
Step Four
Step Four
5. Repeat on the opposite side.
6. Utilizing two people, lift the soft top up and away from
the vehicle, careful to avoid the vehicle’s sport bar,
trim, and tire carrier. Store the soft top in a safe,
clean, and dry location.
Step Six
7. Using the provided #50 Torx head driver and ratchet,
unscrew the Torx screw on both rear corners of the
vehicle, removing the retainers.
Step Seven
I
NSTALLING
T
HE
S
OFT
T
OP
1. If currently installed, remove the hard top
2. Install the door rails, starting with the front, followed
by the rear on each side. For instructions and
appropriate torque specifications for the door rail
3. Install the rear retainers on each side of the rear of
the vehicle using the provided #50 Torx head driver
and ratchet. Refer to the following table for
recommended torque specifications.
Step Three
CAUTION!
Do not overtighten Torx screws. Damage to the
retainers will occur.
2
82
GETTING TO KNOW YOUR VEHICLE
4. Making sure the lift assist mechanism is in the “lock”
position, lift the soft top into the rear of the vehicle
with the side links pointing toward the front. Lower
the lift assist mechanisms onto its retainers on both
sides (on the inside of the sport bar).
Step Four
Step Four
5. Using the provided #40 Torx head driver and ratchet,
tighten the Torx screws by turning them clockwise.
Secure them until they are snug (refer to the following
table for recommended torque specifications), being
careful not to cross-thread the screws or overtighten.
Repeat on the opposite side.
Step Five
Torque
Specification For
Torx Screw
Maximum
Minimum
119.5 in-lb
150.5 in-lb
106.2 in-lb
13.5 N·m
17.0 N·m
12.0 N·m
CAUTION!
Failure to follow the next steps could result in damage
to the Soft Top or vehicle.
1 — Lock Position
2 — Torx Head Screw
3 — Torx Head Screw
Torque
Specification For
Torx Screws
Maximum
Minimum
119.5 in-lb
150.5 in-lb
106.2 in-lb
13.5 N·m
17.0 N·m
12.0 N·m
CAUTION!
Do not overtighten the screws. You can strip the screws
if they are overtightened.
GETTING TO KNOW YOUR VEHICLE
83
(Continued)
2
6. While pulling the release lever on the top of the rail
rearward, place the side link into the guide track on
the top of the rail then release the lever.
Step Six
7. Unsnap and remove the black boot cover. This cover
should be discarded. It was intended as a protective
cover for shipping only.
NOTE:
Be sure the wire harness in the left rear corner is not
tangled in the soft top bows before you lift the top.
H
ARD
T
OP
F
RONT
P
ANEL
(
S
) R
EMOVAL
Use this QR code to access your digital
experience.
CAUTION!
The hard top is not designed to carry any additional
loads, such as after-market roof racks, spare tires,
building materials, hunting or camping supplies, etc.
For optional Mopar® accessory roof racks
Do not move your vehicle until the top has been
either fully attached to the front header, sport bar,
and body side or fully removed.
Failure to follow these cautions may cause interior
water damage, stains or mildew:
It is recommended that the top be free of water prior
to panel removal. Removing the top, opening a door
or lowering a window while the top is wet may allow
water to drip into the vehicle’s interior.
The hard top assembly must be positioned properly
to ensure sealing. Improper installation can cause
water to leak into the vehicle’s interior.
Careless handling and storage of the removable roof
panels may damage the seals, causing water to leak
into the vehicle’s interior.
The front panel(s) must be positioned properly to
ensure sealing. Improper installation can cause
water to leak into the vehicle’s interior.
CAUTION!
84
GETTING TO KNOW YOUR VEHICLE
Four Door Hard Top Components
1 — Right Side Panel
2 — Left Side Panel
3 — Hard Top
GETTING TO KNOW YOUR VEHICLE
85
Two Door Hard Top Components
1 — Right Side Panel
2 — Left Side Panel
3 — Hard Top
2
86
GETTING TO KNOW YOUR VEHICLE
NOTE:
All hard top removal and installation instructions are
applicable to both two and four door model vehicles.
Images shown are of four door models, and appear
-
ance of two door model components may differ.
The left side panel must be removed before removing
the right side panel.
To remove the hard top front panel(s), proceed as follows:
1. Fold down the sun visor against the windshield.
2. Turn the three L-shaped locks on the left side panel
(one at the front, the rear, and outside), unlocking
them from the roof.
Step Two
3. Unlatch the left side header panel latch located at the
top of the windshield.
Step Three
4. Remove the left side panel.
5. Repeat the previous steps to remove the right side
panel.
Hard Top Panel(s) Storage Bag —
If Equipped
The Freedom Top panels storage bag allows you to store
your hard top panels. The storage bag contains two
compartments.
Lay the bag for the Freedom Top panels down so the loops
and hooks are facing upward. Unzip the bag and fold back
the outer flap.
NOTE:
Ensure the front panel latch is closed prior to inserting the
panel into the panels bag.
1. Insert the left side hard top panel into the bag with
the latches facing upward.
2. Unfold the black panel divider (ensure the divider is
lying flat).
3. Insert the right side Freedom Top panel into the bag
with the latches facing downward.
NOTE:
Ensure the front panel latch is closed prior to inserting the
panel into the bag.
4. Unfold the outer flap and zip the hard top bag closed.
Step Four
5. Lift the Freedom Top bag into the vehicle with the
hooks and straps facing the back of the rear seat.
Attach the clip at the bottom of the bag to the child
restraint anchorage, located at the base of the rear
seat.
6. Wrap the upper strap around the rear head restraints
and loop the strap through the buckle. Pull on the
strap to tighten the Freedom Top bag securely
against the rear seat.
1 — Header Panel Latched
2 — Unlatched Position
GETTING TO KNOW YOUR VEHICLE
87
H
ARD
T
OP
F
RONT
P
ANEL
(
S
)
I
NSTALLATION
1. Open the header latch inside the vehicle, and the
three L-shaped locks on each panel.
2. Set the right side panel on the windshield frame with
the locating pin in the front receiver mounting hole
followed by the left side panel, making sure there is
no overhang. Also, make sure that the panels are
sitting flush with the body.
3. Reinstall the panel(s) using the same steps for
removal in reverse order.
NOTE:
To prevent water leaks, the seals and hard top panels
should be clear of any dust and debris prior to reinstal
-
lation.
R
EMOVING
T
HE
H
ARD
T
OP
2. Open both front doors.
3. Using the provided #50 Torx head driver and ratchet,
remove the two Torx head screws that secure the
hard top at the B-pillar (near the top of the front
doors).
Step Three
4. Remove the six Torx head screws that secure the
hard top to the vehicle (along the interior bodyside —
three screws on each side) using the #50 Torx head
driver.
Step Four
5. Open the swing gate all the way to ensure clearance
of the rear window glass. Lift the rear window glass.
Step Five
6. Locate the wire harness and washer hose on the left
rear inside corner of the vehicle.
Step Six
2
88
GETTING TO KNOW YOUR VEHICLE
7. Release the locking tab by pushing it downward.
Step Seven
8. To remove the wiring harness, push the tab inward
while pulling downward to disconnect.
Step Eight
Step Eight
9. To remove the washer hose, push the release button
on hose connector, and pull downward.
Step Nine
10. Secure the wire harness to the body side by plugging
it into the receptacle and reengaging the locking tab.
Step Ten
11. Secure the washer hose by snapping it into the top of
the body side receptacle.
Step Eleven
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст