Jeep Wrangler (2022 year). Manual in english — page 5
GETTING TO KNOW YOUR VEHICLE
75
POWER WINDOWS — IF EQUIPPED
The power window switches are located on the
instrument panel below the climate controls. Push
the switch downward to open the window and
upward to close the window.
The top left switch controls the left front window
and the top right switch controls the right front
window.
Power Window Switches
To open the window part way (manually), push the
window switch down briefly and release.
NOTE:
The power window switches will remain active for
up to 10 minutes after ignition is placed in the OFF
position. Opening either front door will cancel this
feature.
Four-Door Models
The lower left switch controls the left rear
passenger window, and the lower right switch
controls the right rear passenger window.
NOTE:
There are window switches located on the rear of
the center console for the rear passenger windows
in the four-door model.
A
UTO
-D
OWN
F
EATURE
The driver door power and the passenger door
power window switches have an Auto-Down
feature. Push the window switch down to the
second detent and release, and the window will go
down automatically.
To stop the window from going all the way down
during the Auto-Down operation, pull up on the
switch briefly.
WARNING!
Never leave children unattended in a vehicle,
and do not let children play with power windows.
Do not leave the key fob in or near the vehicle, or
in a location accessible to children. Occupants,
particularly unattended children, can become
entrapped by the windows while operating the
power window switches. Such entrapment may
result in serious injury or death.
WARNING!
There is no anti-pinch protection when the
window is almost closed. Be sure to clear all
objects from the window before closing.
2
76
GETTING TO KNOW YOUR VEHICLE
W
INDOW
L
OCKOUT
S
WITCH
Window Lockout Switch
The window lockout switch allows you to disable
the window controls on the rear passenger doors.
To disable the window controls, rotate the switch
downward. To enable the window controls, rotate
the switch upward.
W
IND
B
UFFETING
Wind buffeting can be described as the perception
of pressure on the ears or a helicopter-type sound
in the ears. Your vehicle may exhibit wind buffeting
with the windows down in certain open or partially
open positions. This is a normal occurrence and
can be minimized by adjusting the window
opening.
WRANGLER TOPS
P
ROVIDED
T
OOLS
For your convenience, a tool kit is provided with
your vehicle located in the center console. This kit
includes the necessary tools required for the
operations described in the following sections. All
pieces fit into the ratchet for easy use.
NOTE:
The soft top and the hard top are to be used inde
-
pendently. Your vehicle warranty will not cover
damage resulting from both tops being installed at
the same time.
Provided Tools
If your vehicle is equipped with a Dual Top (four
door models only), the soft top system will be
provided in a separate box located in the rear of
the vehicle for shipping purposes only.
L
OWERING
T
HE
S
OFT
T
OP
I
NTO
S
UNRIDER
® P
OSITION
Use this QR code to access your
digital experience.
1 — Ratchet
2 — #T50 Torx Head Driver
3 — #T40 Torx Head Driver
4 — 15 mm Socket
WARNING!
The fabric quarter windows and fabric top are
designed only for protection against the
elements. Do not rely on them to contain occu
-
pants within the vehicle or to protect against
injury during an accident. Remember, always
wear seat belts.
Make sure hands and fingers are clear of all
pinch points when installing and removing the
soft tops. The lift assist mechanism and side
bows may cause serious injury if fingers or
hands get caught in between.
GETTING TO KNOW YOUR VEHICLE
77
(Continued)
If the temperature is below 72°F (24°C) and/or
the top has been folded down for a period of time,
the top will appear to have shrunk when you raise
it, making it difficult to put up. This is caused by a
natural contraction of the vinyl or acrylic materials
of the fabric top.
Place the vehicle in a warm area. Pull steadily on
the top fabric. The vinyl will stretch back to its
original size and the top can then be installed. If
the temperature is 41°F (5°C) or below, do not
attempt to put the top down or roll the rear or side
curtains.
CAUTION!
The soft top is not designed to carry any
additional loads such as roof racks, spare tires,
building, hunting, or camping supplies, and/or
luggage, etc. Also, it was not designed as a
structural member of the vehicle and, thus,
cannot properly carry any additional loads other
than environmental (rain, snow, etc.).
CAUTION!
Do not run a fabric top through an automatic
car wash. Window scratches and wax buildup
may result.
Do not lower the top when the temperature is
below 41°F (5°C). Damage to the top may
result.
Do not move your vehicle until the top has
been either fully attached to the windshield
frame, or fully lowered.
Do not fully lower the top with the windows
installed. Window and top damage may occur.
For important information on cleaning and
caring for your vehicle's fabric top
Do not use any tools (screwdrivers, etc.) to pry
or force any of the clamps, clips, or retainers
securing the soft top. Do not force or pry the
soft top framework when opening or closing.
Damage to the top may result.
Failure to follow these cautions may cause
interior water damage, stains or mildew on the
top material:
It is recommended that the top be free of
water prior to opening it. Operating the top,
opening a door or lowering a window while the
top is wet may allow water to drip into the
vehicle's interior.
Careless handling and storage of the soft top
may damage the seals, causing water to leak
into the vehicle's interior.
The soft top must be positioned properly to
ensure sealing. Improper installation can
cause water to leak into the vehicle's interior.
CAUTION!
2
78
GETTING TO KNOW YOUR VEHICLE
Four Door Side View Components
1 — #1 Bow
6 — #6 Bow
2 — #2 Bow
7 — Front Window Retainer
3 — #3 Bow
8 — Lower Window Retainer
4 — #4 Bow
9 — Rear Quarter Window
5 — #5 Bow
GETTING TO KNOW YOUR VEHICLE
79
Two Door Side View Components
1 — #1 Bow
6 — #6 Bow
2 — #2 Bow
7 — Front Window Retainer
3 — #3 Bow
8 — Lower Window Retainer
4 — #4 Bow
9 — Rear Quarter Window
5 — #5 Bow
2
80
GETTING TO KNOW YOUR VEHICLE
Two And Four Door Rear Components
1 — Rear Window Retainer Attachment Points
2 — Quarter Window Pillars
3 — Swing Gate Bar Retainers
GETTING TO KNOW YOUR VEHICLE
81
NOTE:
All lowering and raising the soft top instructions
are applicable to both two and four door model
vehicles.
Images shown are of four door models, and
appearance of two door model components
may differ.
The following options are available to you when
lowering your vehicle’s soft top:
Sunrider® position with rear and quarter
windows installed
Sunrider® position with rear and quarter panels
removed
Sunrider® position with rear window installed
and quarter panels removed
Fully lowered position with rear and quarter
windows removed
Both quarter windows should be removed and
installed together.
Lowering The Soft Top Into Sunrider® Position
1. Fold both sun visors forward against the
windshield.
2. Release the header latches from the crossbar
by pulling the handle downward. Make sure
the hook is disengaged from its receiver.
Step Two
3. From both the left and right sides, lift up on the
#1 Bow of the soft top to start the operation.
Step Three
4. Move to the side of the vehicle and use the
side link to fold the soft top rearward into the
Sunrider® position.
Step Four
NOTE:
If leaving the soft top in the Sunrider® position,
secure the top by using the two hook-and-loop
fasteners provided in the center console.
Step Four
2
82
GETTING TO KNOW YOUR VEHICLE
NOTE:
The vehicle can be driven in the Sunrider® posi
-
tion with the rear window and quarter panel
assemblies fully installed or completely
removed.
The rear window and rear quarter windows must
be removed before fully lowering the soft top to
prevent damage to the top. Clean the side and
rear windows before removal to assist in
preventing scratching during removal of the soft
top. If the plastic retainers are difficult to
operate due to road dust, etc., clean them with
a mild soap solution and a small brush. Cleaning
products are available through an authorized
dealer.
Removing The Soft Top Windows
NOTE:
Before fully lowering the soft top, the rear window
and rear quarter windows must be removed.
Remove The Rear Window:
1. With the swing gate open, remove the rear
window’s plastic retainers from the lower
right and left corners.
Step One
2. Grab the swing gate bar, rotate it outward and
upward releasing it from both the right and left
retainers.
Step Two (Left Side Shown)
3. While holding the window in place, slide the
swing gate bar to the left separating it from the
rear window. Store in soft window bag (if
equipped), or a safe location.
Step Three
4. Remove the plastic retainers from both
quarter window pillars.
Step Four
GETTING TO KNOW YOUR VEHICLE
83
5. While keeping the rear window level, slide to
the left until it is completely separate from its
retainer. Do not pull downward while removing
the rear window. Damage to the retainer could
result.
Step Five
Remove The Right And Left Quarter Windows:
1. Through the rear opening, push the bottom
corner outward and release tab from the
bottom of the window pillar.
Step One
2. Undo the hook-and-loop fastener located at
the upper front corner of each quarter window.
Step Two
3. Starting at the rear of the vehicle, remove
plastic retainer from along the bottom of the
window moving toward the front of the vehicle.
Step Three
4. Remove plastic retainer from the bottom to the
top of the front window.
Step Four
2
84
GETTING TO KNOW YOUR VEHICLE
5. While keeping the window level, slide rearward
until it is completely separate from its retainer.
Do not pull downward while removing the
window. Damage to the retainer could result.
Step Five
6. Store in soft window bag (if equipped) or a safe
location.
NOTE:
For information on the use of the storage bag, refer
to the next section.
Soft Top Window Storage Bag —
If Equipped
To safely store the soft top rear window, and rear
quarter windows, proceed as follows:
NOTE:
The swing gate bar, once removed from the rear
window, does not store in the soft window storage
bag (if equipped).
1. With the bag opened completely, fold both
fabric dividers downward and lay the first
quarter window all the way to the right side
with the inside of the window facing
downward and the window pillar to the
outside.
NOTE:
The quarter windows are marked “1” and “2” on
the inside of the window pillar.
Step One
Step One
2. Fold the first divider upward, covering the first
quarter window.
Step Two
1 — Quarter Window Facing Downward
2 — Both Dividers Folded Down
GETTING TO KNOW YOUR VEHICLE
85
3. Lay the second quarter window on top of the
first divider all the way to the left side with the
inside of the window facing downward and the
window pillar to the outside.
Step Three
4. Fold the second divider upward, covering the
second quarter window.
Step Four
5. Lay the rear window on top of the second
divider.
Step Five
6. Close the storage bag and store in a safe
location.
Step Six
Lowering The Soft Top All The Way
1. Remove the rear window and quarter panel
2. From the Sunrider® position
remove straps if previously secured and move
to the rear of the vehicle.
1 — Quarter Window Facing Downward
2 — Second Divider Folded Down
2
86
GETTING TO KNOW YOUR VEHICLE
3. Locate the Sunrider® latch beneath the #6
Bow of the soft top on the left side.
Step Three
4. Pull the latch to release the top, and allow the
soft top to slide rearward freely in the guide
tracks to the stowed position.
Step Four
5. While pushing downward slightly on the folded
soft top, slide the lock lever on the left and
right side lift assist mechanisms to the “lock”
position.
Step Five (Locked Position)
6. Once the lock lever is in the “lock” position,
push downward on each side of the folded soft
top to ensure it is secure. An audible “click”
may be heard.
Step Six
NOTE:
Secure the top by using the two hook-and-loop
fasteners provided in the center console.
Step Six
CAUTION!
Failure to follow the next steps could result in
damage to the Soft Top or vehicle.
GETTING TO KNOW YOUR VEHICLE
87
R
AISING
T
HE
S
OFT
T
OP
Use this QR code to access your
digital experience.
Raising The Soft Top From The
Fully Lowered Position
1. From the fully lowered
position, remove straps if
previously secured.
2. While pushing down on the rear of the top,
slide the lock lever on the left and right side lift
assist mechanisms to the “unlock” position.
Step Two
3. Push up and forward from the #5 Bow along
the guide track until it locks into the Sunrider®
position with an audible “click”.
Step Three
4. Gently pull rearward on the #6 Bow to ensure
the top is locked in the Sunrider® position.
5. Using the side link, lift and push the soft top
toward the front of the vehicle manually
guiding the top into the closed position.
Step Five
Step Five
CAUTION!
Failure to follow the next steps could result in
damage to the Soft Top or vehicle.
1 — Unlocked Position
2 — #5 Bow Location
2
88
GETTING TO KNOW YOUR VEHICLE
6. From inside the vehicle, pull the handle on the
header latch downward to engage the hook
into its receiver. Repeat on the other side.
Step Six
7. Pull the handle back upward while squeezing
the hook, locking the latch into place.
Step Seven
Installing The Soft Top Windows
Install The Right And Left Quarter Windows
1. From the rear of the vehicle, guide the top of
the window into the retainer and slide forward
while keeping the window level. Repeat on
the other side.
Step One
2. Place the top of the quarter window pillar into
the top cover, and insert the bottom tab into
the clip.
Step Two
Step Two
CAUTION!
Failure to follow all Quarter Window Install steps
could result in damage to the Soft Top or vehicle.
GETTING TO KNOW YOUR VEHICLE
89
3. Engage the retainers on the front of the
windows, ensuring they are fully engaged,
followed by the retainers along the bottom of
the windows.
Step Three
NOTE:
It is critical that the retainers are fully engaged
before the vehicle resumes motion.
4. Secure the hook-and-loop fastener at the
upper front corner of each quarter window by
pressing firmly.
Step Four
Install The Rear Window
1. Guide the rear window into the retainer from
left to right while keeping the window level.
Step One
2. Insert the swing gate bar into the retainers at
the bottom of the window from left to the right.
Step Two
3. Rotate the swing gate bar into the left and right
side retainers.
Step Three
4. Line up the rear window to the right side
quarter window first, and engage the plastic
retainers.
1 — Retainer At Front Of Quarter Window
2 — Retainer At Bottom Of Quarter Window
2
90
GETTING TO KNOW YOUR VEHICLE
5. Repeat with the left side quarter window.
Step Five
6. Engage the rear window retainers in the lower
right and left corners.
Step Six
NOTE:
For information on removing your soft top, refer to
the next section.
R
EMOVING
T
HE
S
OFT
T
OP
Use this QR code to access your
digital experience.
2. Make sure the lift assist mechanism on both
the left and right sides are in the “lock”
position, and an audible “click” is heard when
pushing down on the #1 bow from each of the
lift assist mechanisms before removing.
Step Two
3. Using the provided #40 Torx head driver and
ratchet, unscrew the two Torx head screws on
each lift assist mechanism, then lift the
mechanism up and away from the vehicle.
Step Three
CAUTION!
Failure to follow the next steps could result in
damage to the Soft Top or vehicle.
1 — Lock Position
2 — Torx Head Screw
3 — Torx Head Screw
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст