Jeep Liberty KJ. Manual — part 21
SPECIAL TOOLS
REAR SUSPENSION
BALL JOINT PRESS - C-4212F
REMOVER / INSTALLER REAR UPPER BALL JOINT
- 8861
REMOVAL / INSTALLATION REAR UPPER CONTROL
ARM BUSHINGS - 8860
REAR LOWER CONTROL ARM BUSHING
REMOVER/INSTALLER - 8862
2 - 34
REAR
KJ
BUSHINGS
REMOVAL
LOWER SUSPENSION ARM BUSHING
1. Remove the lower suspension arm (Refer to 2 -
SUSPENSION/REAR/LOWER CONTROL ARM -
REMOVAL).
2. Secure the suspension arm in a vise.
NOTE: Extreme pressure lubrication must be used
on the threaded portions of the tool. This will
increase the longevity of the tool and insure
proper operation during the removal and installa-
tion process.
3. Install special tools 8862-4 (receiver)(2), 8862-5
(spacer)(3) and 8862-1 or 8862- 2 (driver)(4) with
the threaded rod 8839 (1) and the bearing as
shown
4. Press out the bushing.
UPPER SUSPENSION ARM BUSHING
1. Remove the upper suspension arm (Refer to 2 -
SUSPENSION/REAR/UPPER CONTROL ARM -
REMOVAL).
2. Secure the suspension arm in a vise.
NOTE: Extreme pressure lubrication must be used
on the threaded portions of the tool. This will
increase the longevity of the tool and insure
proper operation during the removal and installa-
tion process.
3. Install special tools 8853-3 (driver)(1), 8860-1
(receiver)(2) and with the threaded rod 8838 (3)
and the bearing as shown
4. Press out the bushing.
INSTALLATION
LOWER SUSPENSION ARM BUSHING
NOTE: Extreme pressure lubrication must be used on the threaded portions of the tool. This will increase
the longevity of the tool and insure proper operation during the removal and installation process.
KJ
REAR
2 - 35
1. Install the new lower suspension arm bushings into
the lower suspension arm using tools 8862-3 (driv-
er)(1), 8862-4 (receiver)(3), 8862-5 (spacer)(2) and
the bearing with the threaded rod 8839 (4) making
sure to properly orient the bushing in the suspen-
sion arm.
2. Remove the suspension arm from the vise.
3. Install the lower suspension arm (Refer to 2 - SUS-
PENSION/REAR/LOWER
CONTROL
ARM
-
INSTALLATION).
UPPER SUSPENSION ARM BUSHING
NOTE: Extreme pressure lubrication must be used on the threaded portions of the tool. This will increase
the longevity of the tool and insure proper operation during the removal and installation process.
1. Install the new upper suspension arm bushings into
the upper suspension arm using tools 8835-3
(receiver)(2), 8860-2 (driver)(3) and the bearing
with the threaded rod 8838 (1) making sure to
properly orient the bushing in the suspension arm.
2. Remove the suspension arm from the vise.
3. Install the upper suspension arm (Refer to 2 -
SUSPENSION/REAR/UPPER CONTROL ARM -
INSTALLATION).
2 - 36
REAR
KJ
SHOCK
REMOVAL
1. Raise and support the vehicle. Position a hydraulic
jack under the axle to support the axle.
CAUTION: Do not allow the axle to hang from the
upper suspension arm ball joint.
2. Remove the upper nut and bolt (1) from the frame
bracket.
3. Remove the lower nut and bolt (2) from the axle
bracket. Remove the shock absorber.
INSTALLATION
1. Install the shock absorber in the frame bracket and
install the bolt and nut (1).
2. Install the shock absorber in the axle bracket and
install the bolt and nut (2).
3. Remove the supports and lower the vehicle.
4. Tighten the upper mounting nuts (1) to 108 N·m
(80 ft. lbs.). Tighten the lower mounting nuts (2) to
115 N·m (85 ft. lbs.).
KJ
REAR
2 - 37
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст