Jeep Liberty KJ. Manual — part 1436
CD CHANGER
DESCRIPTION
The CD changer (if equipped) is mounted in the cargo
area of the passenger compartment on the right rear
quarter panel.
OPERATION
The CD changer will only operate when the ignition switch is in the On or Accessory positions, and the radio is
turned on. The six-CD magazine may be ejected with the ignition in the Off position.
REMOVAL
1. Disconnect and isolate the battery negative cable.
2. Remove the right rear quarter trim panel. (Refer to
23 - BODY/INTERIOR/QUARTER TRIM PANEL -
REMOVAL).
3. Disconnect the electrical wire harness connector.
8A - 48
AUDIO/VIDEO
KJ
4. Remove the mounting fasteners.
5. Remove the CD Changer (1) from the vehicle.
INSTALLATION
1. Install the CD Changer to the vehicle.
2. Install and tighten the mounting fasteners.
3. Connect the wire harness connector.
4. Install the right rear quarter trim panel (Refer to 23
-
BODY/INTERIOR/QUARTER
TRIM
PANEL
-
INSTALLATION).
5. Connect the battery negative cable.
KJ
AUDIO/VIDEO
8A - 49
INSTRUMENT PANEL ANTENNA CABLE
REMOVAL
DOMESTIC
WARNING: Disable the airbag system before attempting any steering wheel, steering column, seat belt ten-
sioner, side airbag, or instrument panel component diagnosis or service. Disconnect and isolate the battery
negative (ground) cable, then wait two minutes for the airbag system capacitor to discharge before per-
forming further diagnosis or service. This is the only sure way to disable the airbag system. Failure to take
the proper precautions could result in accidental airbag deployment and possible personal injury.
1. Disconnect and isolate the battery negative cable.
2. Remove the instrument panel (Refer to 23 - BODY/
INSTRUMENT
PANEL/INSTRUMENT
PANEL
ASSEMBLY - REMOVAL).
CAUTION: Pulling the antenna cable straight out
of the radio without pulling on the locking antenna
connector could damage the cable or radio.
3. Disconnect the antenna cable from radio by pulling
the locking antenna connector (2) away from radio.
4. Disengage each of the retainers that secure the
cable to the instrument panel.
5. Remove the cable (1) from the instrument panel.
EXPORT
WARNING: Disable the airbag system before attempting any steering wheel, steering column, seat belt ten-
sioner, side airbag, or instrument panel component diagnosis or service. Disconnect and isolate the battery
negative (ground) cable, then wait two minutes for the airbag system capacitor to discharge before per-
forming further diagnosis or service. This is the only sure way to disable the airbag system. Failure to take
the proper precautions could result in accidental airbag deployment and possible personal injury.
8A - 50
AUDIO/VIDEO
KJ
1. Disconnect and isolate the battery negative cable.
2. Remove the instrument panel (Refer to 23 - BODY/
INSTRUMENT
PANEL/INSTRUMENT
PANEL
ASSEMBLY - REMOVAL).
CAUTION: Pulling the antenna cable straight out
of the radio without pulling on the locking antenna
connector could damage the cable or radio.
3. Disconnect antenna cable from radio by pulling on
the locking antenna connector (2)
.
4. Disengage each of the retainers that secure the
cable (2) to the instrument panel.
INSTALLATION
DOMESTIC
WARNING:
Disable
the
airbag
system
before
attempting any steering wheel, steering column,
seat belt tensioner, side airbag, or instrument
panel component diagnosis or service. Disconnect
and isolate the battery negative (ground) cable,
then wait two minutes for the airbag system
capacitor to discharge before performing further
diagnosis or service. This is the only sure way to
disable the airbag system. Failure to take the
proper precautions could result in accidental air-
bag deployment and possible personal injury.
1. Position the instrument panel antenna cable onto
the instrument panel.
2. Engage each of the retainers that secure the cable
to the back side of the instrument panel.
KJ
AUDIO/VIDEO
8A - 51
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст