Jeep Liberty KJ. Manual — part 945
2. Install the tow hooks, if equipped (Refer to 13 -
FRAME & BUMPERS/FRAME/REAR TOW HOOK -
INSTALLATION).
3. Install the trailer hitch, if equipped (Refer to 13 -
FRAME & BUMPERS/FRAME/TRAILER HITCH -
INSTALLATION).
4. Install the bolts and tighten to 88 N·m (65 ft. lbs.).
13 - 28
FRAME & BUMPERS
KJ
FUEL SYSTEM
TABLE OF CONTENTS
page
page
. . . . . . . . . . . . . . . . . 1
. . . . . . . . . . . . . . . 73
FUEL DELIVERY - 3.7L GAS
TABLE OF CONTENTS
page
page
FUEL DELIVERY - 3.7L GAS
OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
STANDARD PROCEDURE
FUEL SYSTEM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
VALVE-FLOW MANAGEMENT
FILTER-FUEL
DESCRIPTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
SENSOR-FUEL LEVEL SENDING UNIT
LINES-FUEL
DESCRIPTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
FITTING-QUICK CONNECT
FITTINGS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
REGULATOR-FUEL PRESSURE
PUMP-FUEL
MODULE-FUEL PUMP
RAIL-FUEL
TANK - FUEL
KJ
FUEL SYSTEM
14 - 1
FUEL DELIVERY - 3.7L GAS
OPERATION
Fuel is picked up in the fuel tank by the fuel pump module. This module is located on the bottom of the fuel tank.
A fuel return system is provided within the fuel pump module using check valves. A separate fuel return line from the
engine to the tank is not used.
The fuel pressure regulator and the main fuel filter are combined within the fuel pump module.
The fuel tank assembly consists of: the fuel tank, fuel pump module assembly, fuel pump module lock ring/gasket,
ORVR components. (Refer to 25 - EMISSIONS CONTROL/EVAPORATIVE EMISSIONS/ORVR - DESCRIPTION)
A fuel filler/vent tube assembly using a pressure/vacuum, 1/4 turn fuel filler cap is used. A one-way check valve is
installed into the tanks fuel fill fitting.
Also to be considered part of the fuel system is the evaporation control system and ORVR system. This is designed
to reduce the emission of fuel vapors into the atmosphere.
Both fuel filters are designed for extended service. They do not require normal scheduled maintenance.
STANDARD PROCEDURE
FUEL SYSTEM PRESSURE RELEASE
Use following procedure if the fuel injector rail is, or is not equipped with a fuel pressure test port.
1. Remove fuel fill cap.
2. Remove fuel pump relay from Power Distribution Center (PDC). For location of relay, refer to label on underside
of PDC cover.
3. Start and run engine until it stalls.
4. Attempt restarting engine until it will no longer run.
5. Turn ignition key to OFF position.
CAUTION: Steps 1, 2, 3 and 4 must be performed to relieve high pressure fuel from within fuel rail. Do not
attempt to use following steps to relieve this pressure as excessive fuel will be forced into a cylinder cham-
ber.
6. Unplug connector from any fuel injector.
7. Attach one end of a jumper wire with alligator clips (18 gauge or smaller) to either injector terminal.
8. Connect other end of jumper wire to positive side of battery.
9. Connect one end of a second jumper wire to remaining injector terminal.
CAUTION: Powering an injector for more than a few seconds will permanently damage the injector.
10. Momentarily touch other end of jumper wire to negative terminal of battery for no more than a few seconds.
11. Place a rag or towel below fuel line quick-connect fitting at fuel rail.
12. Disconnect quick-connect fitting at fuel rail. (Refer to 14 - FUEL SYSTEM/FUEL DELIVERY/QUICK CONNECT
FITTING - STANDARD PROCEDURE)
13. Return fuel pump relay to PDC.
14. One or more Diagnostic Trouble Codes (DTC’s) may have been stored in PCM memory due to fuel pump relay
removal. The DRB
T
scan tool must be used to erase a DTC.
DRAINING FUEL TANK
WARNING: The fuel system may be under constant fuel pressure even with the engine off. This pressure
must be released before servicing fuel tank.
14 - 2
FUEL DELIVERY - 3.7L GAS
KJ
Two different procedures may be used to drain fuel tank: through the fuel fill fitting on tank, or using a diagnostic
scan tool.
The quickest draining procedure involves removing the rubber fuel fill hose (7) from fuel tank fitting.
As an alternative procedure, the electric fuel pump may be activated allowing tank to be drained at fuel rail con-
nection. Refer to appropriate scan tool for fuel pump activation procedures. Before disconnecting fuel line at fuel rail,
release fuel pressure. (Refer to 14 - FUEL SYSTEM/FUEL DELIVERY - STANDARD PROCEDURE) Attach end of
Fuel Pressure Test Adapter 6631 or 6539 at fuel rail disconnection (tool number 6631 is used on 5/16” fuel lines
while tool number 6539 is used on 3/8” fuel lines). Position opposite end of this hose tool to an approved gasoline
draining station. Activate fuel pump and drain tank until empty.
If electric fuel pump is not operating, fuel must be drained through fuel fill fitting at tank. Refer to following proce-
dures.
1. Release fuel system pressure.
2. Raise vehicle.
3. If equipped, remove fuel tank skid plate.
KJ
FUEL DELIVERY - 3.7L GAS
14 - 3
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст