Jeep Liberty KJ. Manual — part 1305
NOTE: With the spare tire removed add 3 mm on the right side to compensate for sag after the spare tire is
installed.
1. Remove the latch striker. (Refer to 23 - BODY/SWING GATE/LATCH STRIKER - REMOVAL)
2. Remove the stabilizer wedge/striker. (Refer to 23 - BODY/SWING GATE/STABILIZER WEDGE - REMOVAL)
3. For hinge side adjustments, loosen the hinge bolts and leave one upper hinge bolt hand tight. (Refer to 23 -
BODY/SWING GATE/HINGE - REMOVAL)
4. Adjust the swing gate to the correct position. (Refer to 23 - BODY/BODY STRUCTURE/GAP AND FLUSH -
SPECIFICATIONS)
5. Tighten the fasteners. (Refer to 23 - BODY/SWING GATE/HINGE - INSTALLATION)
6. Install the latch striker. (Refer to 23 - BODY/SWING GATE/LATCH STRIKER - INSTALLATION)
7. Install the spare tire. (Refer to 22 - TIRES/WHEELS/TIRES/SPARE TIRE - INSTALLATION)
UP/DOWN
NOTE: Up/down swing gate adjustment is done by loosening the hinge to gate fasteners or the hinge to
body fasteners, one hinge at a time and moving the door to the correct position.
NOTE: With the spare tire removed add 3 mm on the right side to compensate for sag after the spare tire is
installed.
1. Remove the latch striker. (Refer to 23 - BODY/SWING GATE/LATCH STRIKER - REMOVAL)
2. Remove the stabilizer wedge/striker. (Refer to 23 - BODY/SWING GATE/STABILIZER WEDGE - REMOVAL)
3. For hinge side adjustments, loosen the hinge bolts and leave one upper hinge bolt hand tight. (Refer to 23 -
BODY/SWING GATE/HINGE - REMOVAL)
4. Adjust the swing gate to the correct position. (Refer to 23 - BODY/BODY STRUCTURE/GAP AND FLUSH -
SPECIFICATIONS)
5. Tighten the fasteners. (Refer to 23 - BODY/SWING GATE/HINGE - INSTALLATION)
6. Install the latch striker. (Refer to 23 - BODY/SWING GATE/LATCH STRIKER - INSTALLATION)
7. Install the spare tire. (Refer to 22 - TIRES/WHEELS/TIRES/SPARE TIRE - INSTALLATION)
LEFT/RIGHT
NOTE: Left/right swing gate adjustment is done by loosening the hinge to body fasteners one hinge at a
time and moving the door to the correct position.
NOTE: With the spare tire removed add 3 mm on the right side to compensate for sag after the spare tire is
installed.
1. Remove the latch striker. (Refer to 23 - BODY/SWING GATE/LATCH STRIKER - REMOVAL)
2. Remove the stabilizer wedge/striker. (Refer to 23 - BODY/SWING GATE/STABILIZER WEDGE - REMOVAL)
3. Loosen the hinge to body bolts and leave one upper hinge bolt hand tight. (Refer to 23 - BODY/SWING GATE/
HINGE - REMOVAL)
4. Adjust the swing gate to the correct position. (Refer to 23 - BODY/BODY STRUCTURE/GAP AND FLUSH -
SPECIFICATIONS)
5. Tighten the fasteners. (Refer to 23 - BODY/SWING GATE/HINGE - INSTALLATION)
6. Install the latch striker. (Refer to 23 - BODY/SWING GATE/LATCH STRIKER - INSTALLATION)
7. Install the spare tire. (Refer to 22 - TIRES/WHEELS/TIRES/SPARE TIRE - INSTALLATION)
23 - 120
SWING GATE
KJ
EXTERIOR
TABLE OF CONTENTS
page
page
BODY SIDE MOLDINGS
COWL GRILLE
EXTERIOR NAME PLATES
FRONT FENDER
FUEL FILL DOOR/HOUSING
GRILLE
GRILLE OPENING REINFORCEMENT
FRONT WHEELHOUSE SPLASH SHIELD
LUGGAGE RACK
REAR WHEELHOUSE SPLASH SHIELD
FRONT WHEEL OPENING FLARE MOLDINGS
REAR WHEEL OPENING FLARE MOLDINGS
RADIATOR CROSSMEMBER
SIDE VIEW MIRROR
GLASS-OUTSIDE REARVIEW MIRROR
SIDE STEP
ROCK RAIL
MOLDING - SILL
KJ
EXTERIOR
23 - 121
BODY SIDE MOLDINGS
REMOVAL
1. Using a trim stick C-4755 or equivalent, remove
and discard the molding (1) from the outside of the
door.
INSTALLATION
1. Thoroughly clean all residue from the body side
molding attachment area of the door.
2. Wipe area clean with a 50% solution of water and
alcohol and wipe dry.
3. Apply new body side molding using the locators in
the door and apply pressure of approximately 40
p.s.i. over the entire surface of the molding.
23 - 122
EXTERIOR
KJ
COWL GRILLE
REMOVAL
1. Remove the hood seal (1).
2. Remove the wiper arms. (Refer to 8 - ELECTRI-
CAL/WIPERS/WASHERS/WIPER
ARMS
-
REMOVAL)
3. Remove the four plastic retainers (2) and remove
the cowl grille (1).
INSTALLATION
1. Position the cowl grille (1) and engage the nine
clips to the bottom of the windshield.
2. Install the four plastic retainers (2).
3. Install the wiper arms. (Refer to 8 - ELECTRICAL/
WIPERS/WASHERS/WIPER ARMS - INSTALLA-
TION)
KJ
EXTERIOR
23 - 123
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст